Husqvarna 1153176-26 KEY to Symbols, Symbols on the machine, Symbols in the operator’s manual

Page 2

KEY TO SYMBOLS

Symbols on the machine:

WARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

•Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

This product is in accordance with applicable EC directives.

Noise emission to the environment according to the European Community’s Directive. The machine’s emission is speciﬁed in chapter Technical data and on label.

Decompression valve: The valve is to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine.

Ignition; choke: Set the choke control in the choke position. This should automatically set the stop switch to the start position.

Adjustment of the oil pump

Chain brake, activated (right)

Chain brake, not activated (left)

Other symbols/decals on the machine refer to special certiﬁcation requirements for certain markets.

2 – English

Symbols in the operator’s manual:

Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

Filling with oil and adjusting oil ﬂow.

The chain brake must be engaged when the chain saw is started.

WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury.

Image 2

Contents 385XP 385XPG 390XP 390XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMufﬂer Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationChecking wear on cutting equipment Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsSafe distance Tree felling techniqueLimbing Felling directionClearing the trunk and preparing your retreat Directional cutsFreeing a trapped tree Freeing a tree that has fallen badlyFelling cut General advice How to avoid kickbackWhat is kickback? Cutting trees and branches that are in tensionCutting the trunk into logs General MaintenanceCarburettor adjustment Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard When the bar hits the stump the brake should be appliedChecking brake band wear Checking the inertia brake releaseChecking the brake trigger ImmediatelyMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springFitting the starter Air ﬁlterSpark plug Must always be replacedNeedle bearing lubrication Adjustment of the oil pumpLubricating the bar tip sprocket Cooling systemWinter use Air Injection centrifugal cleaningTemperature 0C or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gaugesEC-declaration of conformity Applies to Europe onlyPage Original instructions 1153176-26