Husqvarna 1153176-26 manual Basic cutting technique, Terms

Page 23

WORKING TECHNIQUES

the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which will lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting on the pull stroke. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting on the pull stroke gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Basic cutting technique

WARNING! Never use a chain saw by ! holding it with one hand. A chain saw is

not safely controlled with one hand. Always have a secure, firm grip around the handles with both hands.

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke.

Cutting on the push stroke increases the risk of kickback. See instructions under the heading How to avoid kickback.

Terms

Cutting = General term for cutting through wood.

Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the cutting equipment will not jam in the cut.

2Make sure the object you are cutting will not split.

3Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kickback?

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the commonest situations you are likely to encounter when using a chain saw.

English – 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 385XP 385XPG 390XP 390XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerInjuries Some terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingLubricating cutting equipment Tensioning the chainNeedle bearing lubrication Filling with chain oilChecking chain lubrication Chain drive sprocketChecking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fitting a spike bumperFuel Fuel HandlingLong-term storage Fuel safetyFuelling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useJam. Always stop the engine before cleaning Terms Basic cutting techniqueFelling direction Tree felling techniqueLimbing Safe distanceDirectional cuts Clearing the trunk and preparing your retreatFreeing a trapped tree Freeing a tree that has fallen badlyFelling cut Cutting trees and branches that are in tension How to avoid kickbackWhat is kickback? General adviceCutting the trunk into logs General MaintenanceCarburettor adjustment Carburettor without movement limiters Recommended engine speeds are as follows Checking the inertia brake release When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardImmediately Checking the brake triggerMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMust always be replaced Air filterSpark plug Fitting the starterCooling system Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationHeated handles Air Injection centrifugal cleaningTemperature 0C or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityPage Original instructions 1153176-26

1153176-26 specifications

The Husqvarna 1153176-26 is a reliable and innovative addition to the lawn care equipment market, designed specifically to meet the needs of both homeowners and professional landscapers. This product is a hedge trimmer that combines power, precision, and user-friendly features, making it an essential tool for maintaining gardens, hedges, and shrubs.

One of the key features of the Husqvarna 1153176-26 is its robust engine. It is powered by a high-performance, low-emission engine that delivers the power needed for efficient cutting while minimizing environmental impact. This focus on eco-friendliness is a significant technological advancement, setting Husqvarna apart in the competitive outdoor power equipment landscape.

The trimmer is equipped with long, dual-action blades that enhance cutting efficiency and offer improved cutting performance. The length of the blades enables users to tackle larger areas quickly, while the dual-action design reduces vibration, ensuring smoother operation and greater comfort during extended use. This design also contributes to achieving a cleaner cut, which is essential for the health of the plants being trimmed.

Another defining feature of the Husqvarna 1153176-26 is its ergonomic design. The handle is designed to provide comfort and ease of use, allowing operators to maneuver the trimmer with minimal fatigue. Additionally, the soft-grip handles ensure a secure hold, even in challenging conditions.

Safety is paramount in the design of the Husqvarna 1153176-26. The trimmer is equipped with safety features, including a safety lockout system that prevents accidental starts. This ensures that users can work without the constant worry of unintended activation, making it a safe choice for professionals and amateurs alike.

Portability and convenience are also significant considerations in the Husqvarna 1153176-26 design. The lightweight construction makes it easy to transport and operate, while the well-balanced design reduces strain on the arms and shoulders during use.

In summary, the Husqvarna 1153176-26 stands out as a high-quality hedge trimmer, blending power, efficiency, and safety in a user-friendly package. Its advanced engine technology, effective cutting blades, ergonomic design, and focus on safety make it an ideal choice for anyone looking to maintain their landscaping with precision and ease. With this equipment, users can achieve professional results while ensuring their outdoor spaces remain in pristine condition.
Top Page Image Contents