Husqvarna 1153176-26 manual EC-declaration of conformity, Applies to Europe only

Page 42

TECHNICAL DATA

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the chain saws for forest service Husqvarna 385XP, 385XPG, 390XP and 390XPG from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of May 17, 2006 "relating to machinery" 2006/42/EC

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100-2:2003, CISPR 12:2005, EN ISO 11681-1:2004

Notiﬁed body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12, point 3b. The certiﬁcates for EC type examination in accordance with annex IX, have the numbers: 0404/09/2109 - 385XP/XPG, 0404/09/2110 - 390XP/XPG.

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcates have the numbers: 01/161/018 - 385XP/XPG, 01/161/058 - 390XP/XPG.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna December 29, 2009

Bengt Frögelius, Development director chainsaw R&D

(Authorized representative for Husqvarna AB and responsible for technical documentation.)

42 – English

Image 42

Contents 385XP 385XPG 390XP 390XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMufﬂer Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubricationChecking wear on cutting equipment Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsSafe distance Tree felling techniqueLimbing Felling directionClearing the trunk and preparing your retreat Directional cutsFreeing a tree that has fallen badly Felling cutFreeing a trapped tree General advice How to avoid kickbackWhat is kickback? Cutting trees and branches that are in tensionCutting the trunk into logs Maintenance Carburettor adjustmentGeneral Carburettor without movement limiters Recommended engine speeds are as follows Checking the front hand guard When the bar hits the stump the brake should be appliedChecking brake band wear Checking the inertia brake releaseChecking the brake trigger ImmediatelyMufﬂer Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springFitting the starter Air ﬁlterSpark plug Must always be replacedNeedle bearing lubrication Adjustment of the oil pumpLubricating the bar tip sprocket Cooling systemWinter use Air Injection centrifugal cleaningTemperature 0C or colder Heated handles Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gaugesEC-declaration of conformity Applies to Europe onlyPage Original instructions 1153176-26