Husqvarna 1153181-26 manual Fuel Handling, Petrol, Two-stroke oil, Mixing

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of petrol and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

 

 

Petrol

•Use good quality unleaded or leaded petrol.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures. Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel, either Aspen two-stroke fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburettor adjustment may be necessary when changing the type of fuel (see the instructions under the heading Carburettor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

•A poor oil quality and/or too high oil/fuel ratio may jeopardise function and decrease the life time of catalytic converters.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines.

Petrol, litre

Two-stroke oil, litre

 

 

 

 

2% (1:50)

3% (1:33)

 

 

 

5

0,10

0,15

 

 

 

10

0,20

0,30

 

 

 

15

0,30

0,45

 

 

 

20

0,40

0,60

 

 

 

Mixing

•Always mix the petrol and oil in a clean container intended for fuel.

•Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 570 576 XP 576 XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherVibration damping system Stop switchRight hand guard MufflerCutting equipment General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethAdjustment of depth gauge setting General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Sharpening cutting teethCause serious or even fatal injury Tensioning the chainLubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilNeedle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainPetrol Fuel HandlingFuel Two-stroke oilFuel safety FuellingChain oil Transport and storage Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral Checking brake band wear Correctly adjusted carburettorHigh speed jet H Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Must always be replacedRunning when making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Temperature 0C or colderTemperature -5C or colder Fitting the winterising kitHeated handles Electrical carburettor heating576 XPG Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122001, EN ISO 1153181-26

1153181-26 specifications

The Husqvarna 1153181-26 is a highly regarded chainsaw that blends performance, reliability, and user-friendly features. Known for its robustness, this model is designed to meet the needs of both professional users and knowledgeable homeowners. With its powerful engine and innovative technology, the 1153181-26 stands out in the competitive landscape of outdoor power tools.

One of the standout features of the Husqvarna 1153181-26 is its X-Torq engine technology, which significantly reduces fuel consumption and emissions without compromising performance. This two-stroke engine generates substantial power, enabling smooth cutting encounters even with tougher materials. The fuel efficiency achieved through this technology makes it an environmentally friendly option, aligning with modern sustainability goals.

The chainsaw is equipped with an automatic oiling system that ensures proper lubrication of the bar and chain during operation. This feature prolongs the life of the saw and enhances overall cutting performance. Additionally, the adjustable oil pump allows users to control the oil flow according to their needs, making it adaptable for different tasks and conditions.

Another notable characteristic is the lightweight design of the 1153181-26, which improves maneuverability and reduces user fatigue during extended periods of use. The ergonomically designed handle provides a comfortable grip, ensuring better control and precision while cutting. Coupled with a low vibration system, this model minimizes operator fatigue, making it suitable for both novice and seasoned users.

Safety is a core principle in the design of the Husqvarna 1153181-26. It features a chain brake that stops the chain in the event of kickback, protecting the user from potential injuries. The saw also incorporates a protective cover over the chain, safeguarding it during storage and transport.

In conclusion, the Husqvarna 1153181-26 is a versatile and dependable chainsaw that excels in power, efficiency, and safety. With its state-of-the-art features like the X-Torq engine, automatic oiling system, and ergonomic design, it appeals to anyone looking for a reliable tool for outdoor cutting tasks. Whether trimming branches or felling trees, this model provides the performance and comfort needed to accomplish a variety of tasks effectively.
Top Page Image Contents