Husqvarna 1153181-26 Tensioning the chain, Lubricating cutting equipment, Filling with chain oil

Page 14

GENERAL SAFETY PRECAUTIONS

Tensioning the chain

 

!

WARNING! A slack chain may jump off

 

and cause serious or even fatal injury.

 

 

 

 

 

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting ! equipment may cause the chain to snap,

which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which, with its vegetable oil base, is also biodegradable. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 570 576 XP 576 XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherVibration damping system Stop switchRight hand guard MufflerCutting equipment designed to reduce kickback Cutting equipmentGeneral rules Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethAdjustment of depth gauge setting General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Sharpening cutting teethCause serious or even fatal injury Tensioning the chainLubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilNeedle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainPetrol Fuel HandlingFuel Two-stroke oilChain oil Fuel safetyFuelling Transport and storage Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburettor adjustment Checking brake band wear Correctly adjusted carburettorHigh speed jet H Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Must always be replacedRunning when making adjustments Adjustment of the oil pumpAir Injection centrifugal cleaning Needle bearing lubricationWinter use Temperature 0C or colderTemperature -5C or colder Fitting the winterising kit576 XPG Heated handlesElectrical carburettor heating Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEN ISO 12100-22003, Cispr 122001, EN ISO EC-declaration of conformityApplies to Europe only 1153181-26

1153181-26 specifications

The Husqvarna 1153181-26 is a highly regarded chainsaw that blends performance, reliability, and user-friendly features. Known for its robustness, this model is designed to meet the needs of both professional users and knowledgeable homeowners. With its powerful engine and innovative technology, the 1153181-26 stands out in the competitive landscape of outdoor power tools.

One of the standout features of the Husqvarna 1153181-26 is its X-Torq engine technology, which significantly reduces fuel consumption and emissions without compromising performance. This two-stroke engine generates substantial power, enabling smooth cutting encounters even with tougher materials. The fuel efficiency achieved through this technology makes it an environmentally friendly option, aligning with modern sustainability goals.

The chainsaw is equipped with an automatic oiling system that ensures proper lubrication of the bar and chain during operation. This feature prolongs the life of the saw and enhances overall cutting performance. Additionally, the adjustable oil pump allows users to control the oil flow according to their needs, making it adaptable for different tasks and conditions.

Another notable characteristic is the lightweight design of the 1153181-26, which improves maneuverability and reduces user fatigue during extended periods of use. The ergonomically designed handle provides a comfortable grip, ensuring better control and precision while cutting. Coupled with a low vibration system, this model minimizes operator fatigue, making it suitable for both novice and seasoned users.

Safety is a core principle in the design of the Husqvarna 1153181-26. It features a chain brake that stops the chain in the event of kickback, protecting the user from potential injuries. The saw also incorporates a protective cover over the chain, safeguarding it during storage and transport.

In conclusion, the Husqvarna 1153181-26 is a versatile and dependable chainsaw that excels in power, efficiency, and safety. With its state-of-the-art features like the X-Torq engine, automatic oiling system, and ergonomic design, it appeals to anyone looking for a reliable tool for outdoor cutting tasks. Whether trimming branches or felling trees, this model provides the performance and comfort needed to accomplish a variety of tasks effectively.
Top Page Image Contents