Husqvarna 1153181-26 manual Air filter, Spark plug, Lubricating the bar tip sprocket

Page 36

MAINTENANCE

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts.

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburettor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

36 – English

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 570 576 XP 576 XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherStop switch Right hand guardVibration damping system MufflerCutting equipment General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethGeneral advice on adjusting depth gauge setting Increased if the depth gauge setting isAdjustment of depth gauge setting Sharpening cutting teethTensioning the chain Lubricating cutting equipmentCause serious or even fatal injury Which could lead to serious, even fatal injuries Chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelPetrol Two-stroke oilFuel safety FuellingChain oil Transport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsTree felling technique LimbingLog is supported at one end. There is a high risk Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut General advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentGeneral Correctly adjusted carburettor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugLubricating the bar tip sprocket Must always be replacedAdjustment of the oil pump Air Injection centrifugal cleaningRunning when making adjustments Needle bearing lubricationTemperature 0C or colder Temperature -5C or colderWinter use Fitting the winterising kitHeated handles Electrical carburettor heating576 XPG Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 122001, EN ISO 1153181-26

1153181-26 specifications

The Husqvarna 1153181-26 is a highly regarded chainsaw that blends performance, reliability, and user-friendly features. Known for its robustness, this model is designed to meet the needs of both professional users and knowledgeable homeowners. With its powerful engine and innovative technology, the 1153181-26 stands out in the competitive landscape of outdoor power tools.

One of the standout features of the Husqvarna 1153181-26 is its X-Torq engine technology, which significantly reduces fuel consumption and emissions without compromising performance. This two-stroke engine generates substantial power, enabling smooth cutting encounters even with tougher materials. The fuel efficiency achieved through this technology makes it an environmentally friendly option, aligning with modern sustainability goals.

The chainsaw is equipped with an automatic oiling system that ensures proper lubrication of the bar and chain during operation. This feature prolongs the life of the saw and enhances overall cutting performance. Additionally, the adjustable oil pump allows users to control the oil flow according to their needs, making it adaptable for different tasks and conditions.

Another notable characteristic is the lightweight design of the 1153181-26, which improves maneuverability and reduces user fatigue during extended periods of use. The ergonomically designed handle provides a comfortable grip, ensuring better control and precision while cutting. Coupled with a low vibration system, this model minimizes operator fatigue, making it suitable for both novice and seasoned users.

Safety is a core principle in the design of the Husqvarna 1153181-26. It features a chain brake that stops the chain in the event of kickback, protecting the user from potential injuries. The saw also incorporates a protective cover over the chain, safeguarding it during storage and transport.

In conclusion, the Husqvarna 1153181-26 is a versatile and dependable chainsaw that excels in power, efficiency, and safety. With its state-of-the-art features like the X-Torq engine, automatic oiling system, and ergonomic design, it appeals to anyone looking for a reliable tool for outdoor cutting tasks. Whether trimming branches or felling trees, this model provides the performance and comfort needed to accomplish a variety of tasks effectively.
Top Page Image Contents