Husqvarna 1153181-26 manual Basic cutting technique, Terms

Page 25

WORKING TECHNIQUES

the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which will lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting on the pull stroke. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting on the pull stroke gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Basic cutting technique

WARNING! Never use a chain saw by ! holding it with one hand. A chain saw is

not safely controlled with one hand. Always have a secure, firm grip around the handles with both hands.

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke. Cutting on the push stroke increases the risk of kickback. See instructions under the heading How to avoid kickback.

Terms

Cutting = General term for cutting through wood.

Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the cutting equipment will not jam in the cut.

2Make sure the object you are cutting will not split.

3Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kickback?

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the commonest situations you are likely to encounter when using a chain saw.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 570 576 XP 576 XPG Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switchVibration damping system MufflerGeneral rules Cutting equipmentCutting equipment designed to reduce kickback General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingIncreased if the depth gauge setting is General advice on adjusting depth gauge settingAdjustment of depth gauge setting Sharpening cutting teethLubricating cutting equipment Tensioning the chainCause serious or even fatal injury Which could lead to serious, even fatal injuries Chain oilChain drive sprocket Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentBar Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingPetrol Two-stroke oilFuelling Fuel safetyChain oil Long-term storage Transport and storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsJam. Always stop the engine before cleaning Terms Basic cutting techniqueLimbing Tree felling techniqueLog is supported at one end. There is a high risk Safe distanceClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut Freeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburettorChecking brake band wear Checking the front hand guardImmediately Checking the inertia brake releaseMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterLubricating the bar tip sprocket Must always be replacedAir Injection centrifugal cleaning Adjustment of the oil pumpRunning when making adjustments Needle bearing lubricationTemperature -5C or colder Temperature 0C or colderWinter use Fitting the winterising kitElectrical carburettor heating Heated handles576 XPG Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122001, EN ISO 1153181-26

1153181-26 specifications

The Husqvarna 1153181-26 is a highly regarded chainsaw that blends performance, reliability, and user-friendly features. Known for its robustness, this model is designed to meet the needs of both professional users and knowledgeable homeowners. With its powerful engine and innovative technology, the 1153181-26 stands out in the competitive landscape of outdoor power tools.

One of the standout features of the Husqvarna 1153181-26 is its X-Torq engine technology, which significantly reduces fuel consumption and emissions without compromising performance. This two-stroke engine generates substantial power, enabling smooth cutting encounters even with tougher materials. The fuel efficiency achieved through this technology makes it an environmentally friendly option, aligning with modern sustainability goals.

The chainsaw is equipped with an automatic oiling system that ensures proper lubrication of the bar and chain during operation. This feature prolongs the life of the saw and enhances overall cutting performance. Additionally, the adjustable oil pump allows users to control the oil flow according to their needs, making it adaptable for different tasks and conditions.

Another notable characteristic is the lightweight design of the 1153181-26, which improves maneuverability and reduces user fatigue during extended periods of use. The ergonomically designed handle provides a comfortable grip, ensuring better control and precision while cutting. Coupled with a low vibration system, this model minimizes operator fatigue, making it suitable for both novice and seasoned users.

Safety is a core principle in the design of the Husqvarna 1153181-26. It features a chain brake that stops the chain in the event of kickback, protecting the user from potential injuries. The saw also incorporates a protective cover over the chain, safeguarding it during storage and transport.

In conclusion, the Husqvarna 1153181-26 is a versatile and dependable chainsaw that excels in power, efficiency, and safety. With its state-of-the-art features like the X-Torq engine, automatic oiling system, and ergonomic design, it appeals to anyone looking for a reliable tool for outdoor cutting tasks. Whether trimming branches or felling trees, this model provides the performance and comfort needed to accomplish a variety of tasks effectively.
Top Page Image Contents