Hustler Turf Lawn Mower manual Seat adjustment, Control lever adjustment, Steering linkage

Page 91

ADJUSTMENTS

Introduction

Your FasTrak 44/52 was adjusted before it left the factory and was checked during predelivery setup. However, after start-up and continued use, a certain amount of break-in wear will cause some adjustments to change.

Remain alert for unusual noises, they could be signaling a problem. Visually inspect the machine for any abnormal wear or damage. A good time to detect potential problems is while performing scheduled maintenance service. Correcting the problem as quickly as possible is the best insurance.

Clear away heavy build-up of grease, oil and dirt, especially in the engine and under the seat platform areas; minute dust particle are abrasive to close-tolerance engine and hydraulic assemblies.

Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Hustler service center when assistance is needed.

Seat adjustment

The seat can be adjusted forward and rearward by removing the two cap screws that lock the seat platform in place and pivoting the seat platform up and forward. Then loosen the four cap screws on the underneath side of the operator’s platform. Position the seat where you have the best control of the machine and are the most comfortable and then tighten the cap screws. Fig. 9-23

Control lever adjustment

The control levers can be adjusted for operator comfort. By loosening the cap screws that attaches the upper control lever to the lower lever (Fig. 9-24), the upper control lever can be pivoted to fit the operator’s personal preference.

The control levers can also be adjusted up and down. Remove the cap screws and slide the upper control lever up or down and align the holes in it with the holes in lower lever. Re-install the cap screws and tighten.

The control levers should be adjusted so that they align with each other when in the neutral position.

Steering linkage

The neutral adjustment for the control levers in the neutral position is discussed in this section.

The tractor steering has been factory adjusted to eliminate creeping when the control levers are in the neutral position (Fig. 9-25). However, should the tractor begin to creep, the control lever linkage can be adjusted as follows:

Control Lever Neutral Adjustment

Before considering any adjustment, check the tire air pressure. Unequal tire pressure will cause the tractor to drift to one side. Refer to tire pressure information in the Maintenance section of this manual.

Fine adjustment to the unit’s steering is made with the adjustable pump linkage rods. Fig. 9-26

Neutral is properly adjusted when the control levers are in the neutral position and the drive wheels are not turning.

If the tractor creeps in the neutral position the control linkage may be adjusted as follows:

1.Raise and block the tractor up so the drive wheels are off of the floor.

WARNING: Never work under the machine or attachment unless it is safely supported with jack stands. Make certain machine is secure when it is raised and placed on the jack stands. The jack stands should not allow the machine to move when the engine is running and the drive wheels are rotating. Use only certified jack stands. Use only appropriate jack stands, with a minimum weight rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the vehicle stands.

2.Position the control lever in the neutral position. Disengage the deck clutch switch Fig. 9-25.

3.Loosen the nut on the steering dampener’s rear ball stud. Fig. 9-26

Cap screw

Operator’s

platform

Figure 9-23

Upper

control

lever

Cap screw

Lower control

lever

Figure 9-24

Control

lever

Control lever in the

neutral position

Figure 9-25

4.Remove the cotter key that connects the brake link to the brake pawl. Remove the brake link from the brake pawl. Fig. 9-30

5.Start the engine and observe which way the wheels are rotating.

6.If wheel(s) are rotating forward, loosen the jam nuts on the pump linkage rods and rotate the rod to lengthen the steering control linkage until the wheel(s) come to a stop. Fig. 9-26

NOTE: The left linkage controls the left integrated pump/motor and the right linkage controls the right integrated pump/motor.

Repeat for the opposite side if necessary.

365262 4/07

9-15

Image 91
Contents 44 & 52 Deck Parts Manual This spark ignition system complies with Canadian ICES-002 Table of Contents Deck Pulley Assembly -10 Blade Spindle Assembly Breakdown Frequently Ordered Parts General InformationHardware Description Codes & Abbreviations Contents Rivet NUT, 5/16-18 Thread Tractor Frame Rivet Nut InstallationFastrak Frame Idler Plate Idler Plate Rivet Nut InstallationEngine Guard Engine Guard Rivet Nut InstallationFloor Plate Footrest AssemblyLower Step Tread Upper Step Tread365262 4/07 Contents Battery Installation Battery VU1LH-8 Battery Clamp StrapPositive Battery Cable Negative Battery CableDeck Lift Assembly Deck Lift Spring Height Adjustor StopDeck Lift Indicator Stop HandleSteering and Brake Assembly Push Button Switch Fixed Assembly Pump RODLH Pump ROD Adjuster Assembly RH Pump ROD Adjuster AssemblyHydro Transmission Installation Pump Idler Section Pump Belt00OD, 5/8ID Idler Pulley Uhmw BushingTOW Release Link Towlink InstallationFor Mowers with Kohler Engines For Mowers with Honda EnginesContents Honda 18 & 20 HP Engine Installation Honda 20HP Engine Fastrak Wire HarnessSMALL/SHORT Wire TIE Clutch Wire Harness PigtailHonda 16 HP Engine Installation Honda Muffler Gasket Fastrak 16 Honda Wire HarnessHonda 16 HP Engine Honda MufflerBriggs & Stratton 17.5 HP Engine Installation Battery Cable SMALL, Short Wire TIEClutch Pigtail Wire Harness Fastrak 17.5 Wire HarnessKohler 18 & 20 HP Engine Installation Kohler 18 HP SV540S Engine FST 44/52 Kohler Wire HarnessRED 9 Battery Cable Clutch PIGTAIL, Wire Harness365262 4/07 This page intentionally left blank Fuel System Installation Fuel Tank 90 Fitting Fuel Tank CAPFuel Tank Fuel LineInstrument Panel Assembly/Installation KEY Switch PTO SwitchRED Indicator Light KEY AssemblyHonda 18 & 20 HP Electrical Schematic Honda 18 & 20 HP Electrical Schematic Honda 16 HP Electrical Schematic Honda 16 HP Electrical Schematic Briggs & Stratton Electrical Schematic Briggs & Stratton Electrical Schematic Kohler Electrical Schematic Kohler Electrical Schematic 365262 4/07 Contents Front Wheel Assembly Roller Bearing Front Wheel Breakdown-768044Bearing CAP Drive Wheel Assembly-783134 Choke & Throttle Cable Bracket Anti-Rollover Wheel Assembly-Honda and BriggsAnti Scalp Wheel Assembly Muffler Guard365262 4/07 Contents Deck Assembly NT .50-13 HX JAM Znyc Deck PIN & ROD AssemblyFastrak Discharge Chute Discharge Chute Mount BracketDeck Pulley Assembly Idler Slide Uhmw RS Blade Spindle AssemblySection Belt Uhmw Deck Idler Clamp365262 4/07 This page intentionally left blank Deck Assembly 781567 NT .50-13 HX LK NY 546051 358242 Deck 365262 4/07 44Deck Pulley Assembly 365262 4/07 Blade Spindle Assembly Breakdown 365262 4/07 Contents Tractor Assembly Deck Deck InstallationDeck Belt Routing and Tensioning Seat Seat InstallationOperator Presence Switch Seat SupportTractor Decals Deck Decals Tractor Decals Turf Prod Serial no Plate Service DecalBattery Decal Fuel Indicator DecalDeck Decals 727420 365262 4/07 Contents 365262 4/07 Safe Maintenance & Adjustment Practices Maintenance & Adjustment Safety PrecautionsUsing a ramp Safety and Instruction DecalsMaintenance Lubrication IntroductionTorque values TiresFuse Cap screws BatteryAccess to integrated pump/motor units Hydraulic systemBreather hose Nipple Engine Guard Jack stands Lower side plug Drain plug FilterFuel system Fuel Shut-off Valves Honda Fuel filter Belt replacementFuel shutoff valve Engine oil Engine drain plug oil filter Briggs & Stratton HondaDipstick Engine oil Filler tube Engine oil filter Drain plugEngine Belt Pulley Mower blade maintenanceMower blade removal 365262 4/07 365262 4/07 Control lever adjustment Seat adjustmentSteering linkage Link Steering dampenerHydraulic pump belt adjustment Park brake spring adjustmentPark brake switch adjustment AdjustingNut ChainsNut Deck leveling and height adjustmentBolt Adjuster Jam nut Hardware Foot Pedal Nuts Deck lift threaded rod Nut ChainsDeck lift rod Deck liftLift block Assist springsPart Number Index Part Part Part

Lawn Mower specifications

Hustler Turf is well-known for its commitment to crafting high-quality lawn mowers that deliver exceptional performance and durability. Among their standout offerings are the impressive line of zero-turn mowers, designed to make lawn maintenance easier and more efficient.

One of the hallmark features of Hustler Turf lawn mowers is their innovative cutting technology. Equipped with a robust deck design, Hustler mowers provide a clean and precise cut, which is essential for maintaining the health and appearance of any lawn. The decks come in various sizes, allowing users to choose the perfect model suited to their yard’s dimensions. The company also integrates advanced blade systems that optimize airflow and enhance grass clipping discharge, resulting in a superior finish.

Another notable aspect of Hustler Turf mowers is their exceptional maneuverability. The zero-turn capability allows users to navigate around obstacles with ease. This is particularly beneficial for yards with multiple flower beds, trees, and other features that require careful cutting. The controls are intuitively designed, providing a comfortable and responsive experience that allows for precise operation.

Hustler Turf also prioritizes user comfort and safety. Models come equipped with ergonomic seating and handles, helping reduce operator fatigue during extended mowing sessions. Additionally, safety features such as the automatic blade shut-off ensure that the mower operates safely, even when the user exits the seat.

Durability is a core characteristic of Hustler Turf mowers. Constructed with heavy-duty materials and reinforced frames, these machines are built to withstand the rigors of regular use. The longevity of the mowers is complemented by easy serviceability, ensuring that maintenance and repairs are straightforward, allowing owners to keep their machines running optimally for years.

In terms of technology, Hustler Turf has incorporated user-friendly features such as digital displays that provide real-time information about mower performance, including fuel levels and maintenance reminders. Moreover, some models are compatible with advanced GPS and tracking systems, allowing lawn care businesses to manage their fleets with precision.

In conclusion, Hustler Turf lawn mowers are engineered for performance, comfort, and durability. With their innovative technology, user-centered design, and exceptional cutting capabilities, they represent a top choice for both residential homeowners and professional landscapers alike. Whether you are looking to maintain a small yard or take on larger commercial properties, Hustler Turf offers models to meet various needs.