Adjusting Anti-Scalp Wheels & Deck Height Adjustment for Hustler Z4 Mower Models

If the machine’s forward motion must be stopped while mowing, a clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged.

WARNING: Never direct discharge of material from mower deck towards bystanders. Do not operate the mower without either the discharge chute or the entire grass collection system in place. Figure 3-10

Discharge

chute

Figure 3-10

Mower deck operation

DANGER: Never attempt to make any adjustments to the mower deck while the engine is running or with the deck drive clutch engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly.

With the engine running, engage the deck clutch switch (Figure 3-1) and advance engine throttle to full rpm.

NOTE: Engaging the deck clutch at high engine rpm or when under heavy load (in tall grass for example) can cause belts and/or electric clutch to slip, resulting in premature wear or possible damage.

Deck cutting height adjustment

Deck height is adjustable from 1-1/2” to 4-1/2” (3.81 cm -

11.43cm) in 1/4” (.64 cm) increments. The holes in the height adjusting bar are spaced at 1/2” (1.27 cm) intervals. By turning the height adjusting stop around, 1/4” (.64 cm) increments can be attained due to the 1/4” (.64 cm) plate that is part of the stop. Figure 3-11

EXAMPLE: When the height adjusting stop is placed in the 1-1/2” (3.81 cm) hole, with the 1/4” (.64 cm) plate facing to the front of the unit, the cutting height is at 1-1/2”. When the height adjusting stop is placed in the 1-1/2” (3.81 cm) hole, with the 1/4” (.64 cm) plate on the operator’s side of the hole, the cutting height is at 1-3/4” (4.45 cm).

The notch located at the rear of the height adjusting bar is to be used when the deck is placed in the transport mode.

Height adjusting bar

Heightadjusting stop

Figure 3-11

Anti-scalp wheels

Anti-scalp wheel kits are standard on Hustler Mid Mount Z units. These anti-scalp wheels are designed to minimize scalping when mowing on rough uneven terrain.

After setting the cutting height, adjust the front anti-scalp wheels so they extend below the deck but do not contact the ground. They should always be at least 1/4” to 3/4” (6.35mm to 19.05mm) below the deck. With the unit sitting on a flat level surface, the front wheel position can be adjusted up or down as needed from 3/4” to 1-3/4” (19.05mm to 44.45mm) below the blade surface. Move the front wheels up or down, in 1/2” (12.70mm) increments, using the different axle mount holes in the wheel mount bracket. Figure 3-12

When adjusting the rear anti-scalp wheels, the wheel should be in the lower axle mount hole when the front anti-scalp wheels are in the lower or middle axle mount holes. When the front wheels are in the upper axle mount hole, the rear wheels should be in the upper axle mount hole as well.

NOTE: When the anti-scalp wheels are installed, the mini- mum cutting height is 1-1/2” (3.81 cm) with the anti-scalp wheels set at 3/4” (1.91cm).

Anti-scalp wheel

Mount holes

Figure 3-12

602223_0609

3-9

Z4 specifications

The Hustler Turf Z4 is an exceptional zero-turn mower designed for both commercial landscapers and residential users seeking high performance and efficiency. Known for its robust construction and outstanding maneuverability, the Z4 stands out in the competitive field of lawn care equipment.

One of the key features of the Hustler Turf Z4 is its powerful engine options. Equipped with a choice of Kawasaki or Kohler engines, the Z4 delivers reliable performance and impressive torque, ensuring that it can handle tough mowing conditions with ease. The engine options range from 19.5 to 25 horsepower, providing ample power for various lawn sizes and terrain types.

The Z4 features a cutting width of 42 to 54 inches, allowing users to cover large areas in less time. Its innovative cutting deck design promotes superior grass clipping dispersion, leaving behind a clean and even finish. The deck is reinforced for added durability, making it capable of withstanding the rigors of frequent use, whether in commercial landscapes or home lawns.

One of the standout technologies in the Hustler Turf Z4 is the patented SmoothTrak steering system, which allows for precise control and effortless turns. This feature enhances maneuverability around obstacles, flower beds, and tight corners, making mowing a more efficient task. Combined with its low center of gravity, the Z4 offers stability on hills and uneven surfaces.

The Hustler Turf Z4 also prioritizes user comfort and ease of operation. The ergonomic seat design supports long hours of mowing without discomfort, and the intuitive control layout ensures that even novice users can operate the mower with confidence. The easy-to-adjust cutting height allows for quick transitions between different grass types or blooming flowers.

Additionally, the Z4 is equipped with convenient maintenance features. The flip-up deck allows for easy access to the blades for cleaning and sharpening, while the integrated grease fittings simplify lubrication.

In conclusion, the Hustler Turf Z4 is a powerful and versatile zero-turn mower that combines advanced technology with user-friendly features. Designed for performance and durability, it caters to the needs of both professionals and homeowners who demand efficiency and quality in their lawn care equipment. Whether tackling expansive lawns or intricate landscaping, the Z4 rises to the occasion with style and precision.