Hustler Turf Z4 Mower blade removal, Seat adjustment, Control lever adjustment, Standard seat

Page 29

 

Warped Blade (Replace)

 

Cutting

 

plane

Bladewrp.ai

Straight Blade

Comparison of Warped and Straight Blades

 

Figure 9-8

Cutting edge

Twisted Blade Edge

(replace)

Cutting Plane

Cutting edge

Straight Blade Edge

Bladetwt.ai End view of blades, comparing twisted and straightened blades

Figure 9-9

Mower blade removal

Use a 15/16" wrench to remove the 5/8" cap screw holding the blade to the spindle shaft from underneath. NOTE: A blade holding tool (part number 381442) is available from Hustler Turf Equipment. It is designed to prevent the blades from rotating when they are being removed or installed on the spindle. Contact your Hustler dealer for more information.

Sharpen the blades on a grinder following pattern as shown (Figure 9-7). Touch-up sharpening can be done with a file.

Check the blades for balance following grinding. A commercial balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on an inverted line punch or 1/2" bolt. Blade should not lean or tilt. Spin the blade slowly, blade should not wobble. If blade is out of balance, true it up before reinstalling.

Lay the blade on a flat surface and check for distortion (Figure 9-8 & Figure 9-9). Replace any distorted blade.

Do not re-use spindle bolts which have stripped, worn or undercut threads. Torque bolts on spindles to 118 foot-pounds (160.0 nm) when reinstalling blades.

IMPORTANT: When mounting blades, rotate them after installation to ensure blade tips do not touch each other or sides of the mower.

WARNING: Failure to correctly torque the bolt may result in the loss of the blade which can cause serious injury.

WARNING: Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them.

Seat adjustment

There are two seat options available for this machine; standard and suspension. The following are the adjustments for each of these seats.

Standard seat

The standard seat has one adjustment; forward and rearward travel. Figure 9-10

Forward/rearward

travel lever

Figure 9-10

Suspension seat

The suspension seat can be adjusted four different ways to obtain the most comfortable position:

1.Back angle Figure 9-11

2.Forward and rearward travel Figure 9-12

3.Weight Figure 9-12

4.Lumbar Figure 9-13

Back angle

control

Figure 9-11

Control lever adjustment

The steering control levers can be adjusted for operator comfort. By loosening the cap screws that attaches the upper control lever to the lower lever (Figure 9-14), the upper control lever can be pivoted to fit the operator’s personal preference.

The steering control levers should be adjusted so that they align with each other when in the neutral position

9-6

602223_0609

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Page General Information 6022230609 What is Covered by this Warranty Disclaimer of Warranty Safety and Instruction Decals Safety PrecautionsPart Part Number Part Number BJE OFF International SymbolsSlope Guide 6022230609 Operation OperationSafe Operating Practices Slope Operation Using a rampChildren Safety start interlock systemControl Panel ControlsEngine starting Check tractor safety start interlock system daily, prior toMoving tractor with stalled engine Stopping the engineRoll Over Protective Structure Torque values are given belowPossible damage to the Rops Driving the tractorTractor towing Front of Tractor Faces this DirectionOperating suggestions Direction of arrows indicate direction of tractor movementThree point turn Ve oAnti-scalp wheels Deck cutting height adjustmentMower deck operation 6022230609 Service Maintenance & AdjustmentsSafe Servicing Practices IntroductionTires Torque valuesLubrication Electrical systemFuel system Hydraulic systemEngine oil and filter Recommended service procedureEngine air filter OverservicingMower blade maintenance General engine maintenance BeltsControl lever adjustment Seat adjustmentMower blade removal Standard seat6022230609 Hustler Z4 48/54/60 Maintenance Schedule Refer to Fig Hustler Z4 48/54/60 Maintenance Locator Chart Maintenance Locator Chart6022230609 Symptoms Probable Causes Suggested Remedies Hustler Z4 TroubleshootingStorage Preparation of battery for storageProduct Literature Preparation of engine for storageIndex 6022230609

Z4 specifications

The Hustler Turf Z4 is an exceptional zero-turn mower designed for both commercial landscapers and residential users seeking high performance and efficiency. Known for its robust construction and outstanding maneuverability, the Z4 stands out in the competitive field of lawn care equipment.

One of the key features of the Hustler Turf Z4 is its powerful engine options. Equipped with a choice of Kawasaki or Kohler engines, the Z4 delivers reliable performance and impressive torque, ensuring that it can handle tough mowing conditions with ease. The engine options range from 19.5 to 25 horsepower, providing ample power for various lawn sizes and terrain types.

The Z4 features a cutting width of 42 to 54 inches, allowing users to cover large areas in less time. Its innovative cutting deck design promotes superior grass clipping dispersion, leaving behind a clean and even finish. The deck is reinforced for added durability, making it capable of withstanding the rigors of frequent use, whether in commercial landscapes or home lawns.

One of the standout technologies in the Hustler Turf Z4 is the patented SmoothTrak steering system, which allows for precise control and effortless turns. This feature enhances maneuverability around obstacles, flower beds, and tight corners, making mowing a more efficient task. Combined with its low center of gravity, the Z4 offers stability on hills and uneven surfaces.

The Hustler Turf Z4 also prioritizes user comfort and ease of operation. The ergonomic seat design supports long hours of mowing without discomfort, and the intuitive control layout ensures that even novice users can operate the mower with confidence. The easy-to-adjust cutting height allows for quick transitions between different grass types or blooming flowers.

Additionally, the Z4 is equipped with convenient maintenance features. The flip-up deck allows for easy access to the blades for cleaning and sharpening, while the integrated grease fittings simplify lubrication.

In conclusion, the Hustler Turf Z4 is a powerful and versatile zero-turn mower that combines advanced technology with user-friendly features. Designed for performance and durability, it caters to the needs of both professionals and homeowners who demand efficiency and quality in their lawn care equipment. Whether tackling expansive lawns or intricate landscaping, the Z4 rises to the occasion with style and precision.
Top Page Image Contents