Unigreen CAMPO 11 - 16 - 22 - 32 Hook Version Homologated, Parking Foot, Wheel Spacing Adjustment

Page 11

4.4.2 HOOK VERSION (HOMOLOGATED)

=Check that the weight on the hook can be supported by the tractor (the maximum weights on the drawbar are indicated in the fittings tables N° 12 pages 33-34).

=If the machine is coupled to the tractor by a tow hook, adjust the height of the hook to keep the tank of the sprayer horizontal.

=When you have connected the drawbar proceed as for the towing steering drawbar.

Tractor coupling for Towed machines: homologated version, coupled to tow hook

4.4.3 PARKING FOOT

After attaching the drawbar to the tractor, you must retract the parking foot (or wheel) to prevent damage during operation.

Retract the foot as follows:

=lift the machine up about 20 cm using the tractor’s elevator (if the machine is instead attached to the trailer hook, retract the parking foot by turning the knob)

=Take out the blocking pin and push the foot up towards the back of the machine.

=Hold the foot horizontal and put the blocking pin back in, inserting the handle in the slot to keep it from accidentally slipping out.

NOTE: to put the foot back into parking position when you unhook the machine from the tractor after operation, make sure that you follow these instructions:

=hold up the foot with one hand, while pulling out the blocking pin with the other (guide the foot all the way down with your hand).

=put the blocking pin back in, adjust the height to keep the tank of the sprayer horizontal.

4.4.4 WHEEL SPACING ADJUSTMENT

To adjust the wheel spacing, you must lift up the machine as described in 4.3, or use a jack underneath the machine chassis; if you use a jack, the machine must be hooked up to the tractor so it is properly braked.

The correct position for the jack is shown on the machine in the illustration to the side. Check that the jack is resting steadily on a firm, solid surface.

To adjust the spacing, just loosen the screws holding the axle and pull the hub out to the desired position, then secure it again with the screws.

WARNING: axle track should be adjusted by authorized Unigreen personnel. The length (L) of the axle section inserted in the chassis must never be less than the one indicated in the chart, and the overhang (S) must not be greater; incorrect positioning of the hubs could weaken the axle and cause breakage.

Hub chart (measurements in mm)

series

S (max)

L (min)

T

hub

Campo 11

200

350

550

60x60x550 6c

 

Campo 16

175

375

550

60x60x550 6c

Campo 16 Riso

200

500

700

70x70x700 8c

Campo 22 C/E

250

450

700

70x70x700 8c

Campo 22 Riso

250

450

700

80x80x700 8c

Campo 22 P

250

450

700

80x80x700 8c

Campo 32 C/P

250

450

700

80x80x700 8c

Campo 22/32 S

300

400

700

100x100x700 8c

Estrarre la spina di blocco e ribaltare il piede verso il retro della macchina.

Sostenere il piede orizzontalmente e riposizionare la spina di blocco facendo alloggiare la maniglia nell'apposito incavo per evitare sfilamenti accidentali.

unigreen 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 10/2007 USE and Maintenance ManualSummary Hand Lances Hose Reel Maintenance Product Responsibility Unigreen spa is not responsible if GuaranteeComposition of the Manual Improper useKey to the symbols Recommendations Using Chemical ProductsIntended USE Prohibited USEDriving on the Road Machines Designed to be Used only with Clean WaterCharacteristics and Specifications Weather ConditionsUSER’S Instructions Description of the Machine Noise Level of the MachineStandards of Reference Transporting and Moving the Machine Work StationsHand Washing Tanks Preliminary ChecksStandard Version Elevator Coupling Towed Sprayers ParkingTractor Coupling Parking Foot Wheel Spacing AdjustmentHook Version Homologated Cardan Shaft Hydraulic Connection to the DistributorsSuction Filter PumpGeneral Instructions Pressure RegulatorComponents of the Pressure Regulator Control box for Ergo and Remo electrical regulatorsSpraying Computer Optional Premixer on Cover Optional Filling the TankMixing Manual PremixingPressione Premixer on Hopper with TIN Washer OptionalTOP-MIX Premixer for Campo 11-16-22E Optional HOW to USE the LP83 IncorporatorWashing with Full Tank Optional Washing the SprayerCircuit Washer and Tank Washer Indipendent Hydraulic Plant Horizontal Booms for Herbacious CultivationsHydraulic Herbicide Booms Exceed a height of 4 metersVariable Geometry AIR-ASSISTED BoomsSELF-LEVELING Devices Anti-drift nozzles LiftingDescription of Type of Nozzles Fan nozzles=600xQ Useful InformationHose Reel MarkerHand Lances Extraordinary Maintenance MaintenanceProgrammed Maintenance TAB. N Routine MaintenanceElectrical and Electronic Apparatus Waste Eeaw Putting Back Into Service After Winter LayupDemolition and Disposal Materials for DemolitionUnigreen Arancio Orange Verde Green Giallo Yellow BLU Blue Rosso RED TAB.1 Characteristics Nozzles ISORosso RED Marrone Brown TAB.2 Characteristics Nozzles Conical ISOTAB.3-4 Capacity Hand Lances TAB.5-6 Spraying Tables 250050 h 300 h Table of Programmed Maintenance OperationPROBLEMS, Causes and Solutions TAB a TAB.12A Allowed FittingsTAB.12B Allowed Fittings TAB bIL Polietilene Rotazionale Member of the group
Related manuals
Manual 32 pages 5.67 Kb

CAMPO 11 - 16 - 22 - 32, DSP 11 - 16 - 22 - 32 specifications

Unigreen DSP Series and CAMPO Series are advanced agricultural sprayers designed to meet the evolving needs of modern farming. The Unigreen DSP (Dynamic Spraying Product) models 11, 16, 22, and 32, along with the CAMPO models of the same specifications, are engineered for efficiency, precision, and reliability in crop protection.

One of the key features of the Unigreen DSP models is their innovative spraying technology. Each model is equipped with a high-capacity tank that allows for extended operation without the need for frequent refills. The DSP series incorporates adjustable booms that provide precise application across various crop types. This ensures uniform coverage and minimizes waste, making it an environmentally friendly option for farmers.

The CAMPO series also boasts similar tank capacities and boom adjustments, making them suitable for diverse agricultural applications. Both series offer customizable options, allowing farmers to choose the configuration that best fits their land and crop requirements.

Another standout characteristic of both Unigreen and CAMPO sprayers is their user-friendly interface. Equipped with advanced electronic controls, farmers can easily monitor and adjust spray rates, pressure, and other critical parameters in real time. This technology not only enhances the sprayers' operational efficiency but also aids in achieving the optimum application rates for different pesticides and fertilizers.

Furthermore, both series integrate cutting-edge GPS technology, enabling precision agriculture practices. This feature allows operators to map their fields, ensuring that every inch is accurately treated, while also reducing the possibility of overlap or missed areas. This precision application reduces chemical usage and ultimately leads to cost savings.

Durability is another primary focus in the design of the Unigreen DSP and CAMPO sprayers. Built with high-quality materials that can withstand harsh environmental conditions, these sprayers promise longevity and consistent performance over time.

In summary, Unigreen DSP and CAMPO models 11, 16, 22, and 32 are technologically advanced agricultural sprayers that combine efficiency, precision, and durability. With features such as adjustable booms, advanced electronic controls, and GPS technology, they cater to the diverse needs of today’s farmers, helping to enhance productivity while minimizing environmental impact. These sprayers are positioned to play a pivotal role in the future of sustainable agriculture.
Top Page Image Contents