Ryobi Outdoor CS30 RY30020A, SS30 RY30040A, BC30 RY30060A manual MANUFACTURER’S Warranty Coverage

Page 25

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.

RYOBI TECHNOLOGIES, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Ryobi Technologies, Inc. are pleased to explain the Emission Control System Warranty on your non-road or small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model year non-road engines must be designed, built, and equipped, at the time of sale, to meet the U.S. EPA regulations for small non-road engines. The non-road engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser. Ryobi Technologies, Inc. must warrant the emission control system on your non-road or small off-road engine for the period of time listed above provided there has been no abuse, neglect, or improper maintenance of your non-road or small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic converter. Also included may be hoses, belts and connectors, and other emission related assemblies.

Where a warrantable condition exists, Ryobi Technologies, Inc. will repair your non-road or small off-road engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year non- road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by Ryobi Technologies, Inc. free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a)As the non-road or small off-road engine owner, you are responsible for the performance of required maintenance listed in your operator’s manual. Ryobi Technologies, Inc. recommends that you retain all receipts covering maintenance on your non-road or small off-road engine, but Ryobi Technologies, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b)As the non-road or small off-road engine owner, you should be aware, however, that Ryobi Technologies, Inc., may deny you warranty coverage if your non-road or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.

(c)You are responsible for presenting your non-road or small off-road engine to a Ryobi Technologies, Inc., service dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a Ryobi Technologies, Inc., Customer Representative at 1-800-860-4050.

COVERAGE:

Ryobi Technologies, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your non-road or small off-road engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Ryobi Technologies, Inc. also war- rants to the initial purchaser and each subsequent purchaser that your non-road or small off-road engine is free from defects in mate- rials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the non-road or small off- road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Ryobi Technologies, Inc. at no cost to the owner.

Ryobi Technologies, Inc. shall remedy warranty defects at any authorized Ryobi Technologies, Inc. engine dealer or warranty sta- tion. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work deter- mines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty. Ryobi Technologies, Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)

These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by Ryobi Technologies, Inc. in the operator’s manual.

LIMITATIONS

The Emission Control Systems Warranty shall not cover any of the following:

(a)repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or replacements not conforming to Ryobi Technologies, Inc. specifications that adversely affect performance and/or durability, and alterations or modifications not recommended or approved in writing by Ryobi Technologies, Inc., and

(b)replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement point.

The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.

Page 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbol Name Explanation SymbolsService Knob Starter Grip Rope Rear Handle Trigger Lock Primer BulbString Head Features Assembly Removing the Attachment from the Power Head Installing the Power Head to the AttachmentAttaching the Storage Hanger See FigureAttaching the J Handle BC30 Attaching the Front Handle CS30 and SS30To Attach the Curved Shaft Grass Deflector CS30 Attaching the Grass DeflectorTo Attach the Straight Shaft Grass Deflector SS30 Attaching the Brushcutter Guard BC30Converting from Brushcutter to String Trimmer BC30 Attaching the Shoulder Harness BC30Removing the TRI-ARCBLADE and Brushcutter Guard Converting from String Trimmer to Brushcutter BC30Operation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Operating the Trimmer Fueling and Refueling the TrimmerTo Advance the Cutting Line Manually To Advance the Cutting LineCutting Tips Grass Deflector Line Trimming CUT-OFF BladeBlade Thrust Operating the BrushcutterTRI-ARCBLADE Cutting Technique BladeSee Figures 21 Starting and StoppingGeneral Maintenance MaintenanceSpool Replacement See Figures 24See Figures 26 String ReplacementArrows on Spool Anchor Hole First String SlotReplacing and Cleaning AIR Filter Cleaning the Exhaust Port and Muffler Spark ArrestorFuel CAP Spark PlugSpeed. See Figure TroubleshootingIdle Speed Screw Warranty Limited Warranty Statement OWNER’S Warranty Responsibilities MANUFACTURER’S Warranty CoverageMaintenance Requirements CoverageService

CS30 RY30020A, SS30 RY30040A, BC30 RY30060A specifications

The Ryobi Outdoor tools series, featuring the CS30 RY30020A, SS30 RY30040A, and BC30 RY30060A, delivers robust power and convenience for all your gardening and landscaping needs. Known for their reliability and innovative technology, these tools embody Ryobi's commitment to enhancing outdoor experiences.

The CS30 RY30020A is a powerful cordless chainsaw designed for effortless cutting. Equipped with a brushless motor, it delivers high performance and extended runtime, making it ideal for tasks like limbing and pruning. Its lightweight design ensures ease of use, reducing fatigue during prolonged operation. The tool features an automatic oiler that keeps the chain lubricated, enhancing longevity and performance. Additionally, the 10-inch bar and chain offer an excellent balance of maneuverability and cutting capacity, suitable for various wood sizes.

Moving on to the SS30 RY30040A, this string trimmer is engineered for versatility and comfort. The innovative design includes a curved shaft that offers better visibility and control while trimming. The electric motor provides consistent power without the hassle of gas or oil, making it an environmentally friendly option. The SS30 is equipped with a ReelEasy line feeding system, allowing for quick and easy line replacement. With adjustable handles and an ergonomic design, users can easily customize the trimmer for optimal comfort, reducing strain during extended use.

Finally, the BC30 RY30060A brush cutter is an essential tool for tackling overgrown areas and thick brush. Its powerful motor can handle tougher vegetation, while the dual-blade system ensures efficient cutting. The shaft design offers superior reach, making it possible to access hard-to-reach areas easily. The BC30 also features a comfortable grip and shoulder harness, improving stability and reducing fatigue for the user.

All three models are backed by Ryobi's dedication to quality, offering tools that are not only durable but also easy to maintain. With their lightweight construction, advanced technologies, and user-friendly features, the CS30, SS30, and BC30 are perfect companions for anyone seeking to elevate their outdoor maintenance projects while enjoying the benefits of cordless technology. Whether you are a homeowner or a professional landscaper, these Ryobi tools provide reliable performance and efficiency to tackle any outdoor task with confidence.
Top Page Image Contents