Ryobi Outdoor CS30 RY30020A, SS30 RY30040A, BC30 RY30060A Troubleshooting, Speed. See Figure

Page 22

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Engine will not start

1. No spark.

2. No fuel.

\

3. Engine is flooded.

1.Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug.

2.Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a service dealer. If primer bulb fills, engine may be flooded, proceed to next item.

3.Set the start lever to the START position. Squeeze the trigger and pull the rope repeatedly until the engine starts and runs.

NOTE: Depending on the severity of the flooding, this may require numerous pulls of the rope. See

Figure 23.

Engine does not reach full speed and emits excessive smoke

1.Incorrect oil/fuel mixture.

2.Air filter is dirty.

3.Spark arrestor screen is dirty.

4.Spark plug fouled.

1.Use fresh fuel and the correct 2-cycle oil mix. (50:1).

2.Clean air filter. Refer to “Replacing and Cleaning Air Filter” earlier in this manual.

3.Contact a servicing dealer.

4.Clean or replace spark plug. Reset spark plug gap. Refer to “Spark Plug Replacement” earlier in this manual.

Engine starts, runs, and ac-

1.

Idle speed screw on carburetor

1. Turn idle speed screw clockwise to increase idle

 

needs adjustment.

celerates but will not idle

 

 

speed. See Figure 31.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

String will not advance

1. String is welded to itself.

1.

Lubricate string with silicone spray.

 

 

2.

Not enough string on spool.

2.

Install more string. Refer to “String Replacement”

 

 

 

 

 

earlier in this manual.

 

 

3.

String is worn too short.

3.

Pull strings while alternately pressing down on

 

 

 

 

 

and releasing spool retainer.

 

 

4.

String is tangled on spool.

4.

Remove string from spool and rewind. Refer to

 

 

 

 

 

“String Replacement” earlier in this manual.

 

 

5.

Engine speed is too slow.

5.

Advance string at full throttle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IDLE SPEED

SCREW

Fig. 31

Page 22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbols Symbol Name ExplanationService Knob Starter Grip Rope Rear Handle Trigger Lock Primer BulbString Head Features Assembly Attaching the Storage Hanger Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head See FigureAttaching the Front Handle CS30 and SS30 Attaching the J Handle BC30To Attach the Straight Shaft Grass Deflector SS30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 Attaching the Brushcutter Guard BC30Removing the TRI-ARCBLADE and Brushcutter Guard Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Converting from String Trimmer to Brushcutter BC30Operation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer Operating the TrimmerCutting Tips To Advance the Cutting LineTo Advance the Cutting Line Manually Grass Deflector Line Trimming CUT-OFF BladeTRI-ARCBLADE Operating the BrushcutterBlade Thrust Cutting Technique BladeStarting and Stopping See Figures 21Spool Replacement MaintenanceGeneral Maintenance See Figures 24Arrows on Spool Anchor Hole String ReplacementSee Figures 26 First String SlotFuel CAP Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Spark PlugSpeed. See Figure TroubleshootingIdle Speed Screw Warranty Limited Warranty Statement Maintenance Requirements MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities CoverageService

CS30 RY30020A, SS30 RY30040A, BC30 RY30060A specifications

The Ryobi Outdoor tools series, featuring the CS30 RY30020A, SS30 RY30040A, and BC30 RY30060A, delivers robust power and convenience for all your gardening and landscaping needs. Known for their reliability and innovative technology, these tools embody Ryobi's commitment to enhancing outdoor experiences.

The CS30 RY30020A is a powerful cordless chainsaw designed for effortless cutting. Equipped with a brushless motor, it delivers high performance and extended runtime, making it ideal for tasks like limbing and pruning. Its lightweight design ensures ease of use, reducing fatigue during prolonged operation. The tool features an automatic oiler that keeps the chain lubricated, enhancing longevity and performance. Additionally, the 10-inch bar and chain offer an excellent balance of maneuverability and cutting capacity, suitable for various wood sizes.

Moving on to the SS30 RY30040A, this string trimmer is engineered for versatility and comfort. The innovative design includes a curved shaft that offers better visibility and control while trimming. The electric motor provides consistent power without the hassle of gas or oil, making it an environmentally friendly option. The SS30 is equipped with a ReelEasy line feeding system, allowing for quick and easy line replacement. With adjustable handles and an ergonomic design, users can easily customize the trimmer for optimal comfort, reducing strain during extended use.

Finally, the BC30 RY30060A brush cutter is an essential tool for tackling overgrown areas and thick brush. Its powerful motor can handle tougher vegetation, while the dual-blade system ensures efficient cutting. The shaft design offers superior reach, making it possible to access hard-to-reach areas easily. The BC30 also features a comfortable grip and shoulder harness, improving stability and reducing fatigue for the user.

All three models are backed by Ryobi's dedication to quality, offering tools that are not only durable but also easy to maintain. With their lightweight construction, advanced technologies, and user-friendly features, the CS30, SS30, and BC30 are perfect companions for anyone seeking to elevate their outdoor maintenance projects while enjoying the benefits of cordless technology. Whether you are a homeowner or a professional landscaper, these Ryobi tools provide reliable performance and efficiency to tackle any outdoor task with confidence.
Top Page Image Contents