Porter-Cable H450IS instruction manual Connecting Procedure for Raising or Suspending Generator

Page 16

Failure to connect and operate equipment in this sequence can cause damage to equipment and will void the warranty

on your generator.

Follow the wattage calculation table in the Wattage Calculation section of this manual. Overloading the generator will cause power fluctuations and can damage equipment and appliances.

Porter-Cable Corporation will only be responsible for damage to customer's equipment when the generator is determined to be defective. This determination will only be made by an authorized representative of Porter-Cable Corporation and this decision will be final. Porter-Cable Corporation reserves the right to inspect the electrical connections at the customer's site of operation and test the generator for proper operation before any determination of liability is made. Failure to maintain the equipment or wiring for inspection will void any claim for damages by the customer. Porter-Cable Corporation will not be responsible for equipment damaged as a result of voltage surges, improper operation or improper installation of the generator.

CONNECTING PROCEDURE FOR RAISING OR SUSPENDING GENERATOR

Failure to properly connect lifting cables, chains, or straps can cause properly damage, serious injury or death, and void the

manufacturer’s warranty.

Always use cables, chains, or straps rated at 2000 lbs. working load or more to raise or suspend generator.

Never operate generator while suspended. This could cause property damage, serious injury or death.

DO NOT suspend objects other than generator from skyhook.

1.Route cable, chain, or strap through

lift ring as shown. ALWAYS use lift ring when raising or suspending generator.

NOTE: Make sure the generator is in a level position before raising or suspending to prevent damage.

D28512

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Generator Safety Guidelines / Definitions Consumer Safety InformationImportant Safety Instructions Risk of Electrocution and FireWhen installing a Double Risk of Electrocution and FireBe used OperationUnit Indoors or in ANY Risk of FireConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe Operation Risk of Moving Parts Risk of HOT SurfacesRisk from Lifting Consumer General and Service Information SpecificationsRead and understand all safety warnings H450ISAssembly Remove Generator from CartonOther Loose Parts Grounding the GeneratorDouble Throw Transfer Switch Extension Cord Wire Gauge Chart Length Size AmperageObtaining Electricity from the Generator Extension CordsTools needed Assemble SkyhookParts bag contains Operation Know Your GeneratorIdle Control Choose the correct applicationTo Start the Engine Deadly gasConnecting Electrical Loads Stopping EngineConnecting Procedure for Raising or Suspending Generator Maintenance Engine Preparation StorageGenerator Determining Wattage Requirements Wattage CalculationsRunning Watts Starting Watts Starting Wattage Requirements Volts X Amp = Watts Example 120 volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserQuick Facts

H450IS specifications

The Porter-Cable H450IS is a high-performance, lightweight electric hammer drill designed to meet the needs of both professionals and DIY enthusiasts. Renowned for its versatility and durability, the H450IS is ideal for various applications including drilling in wood, metal, and masonry, as well as for driving screws efficiently.

One of the standout features of the H450IS is its powerful motor that delivers an impressive amount of torque, making it capable of handling tough materials with ease. The tool boasts a variable speed trigger, allowing users to control the speed for precise drilling. This feature is especially beneficial when working with delicate materials that require a gentler touch.

The H450IS is equipped with a dual-mode operation, allowing users to switch between rotary drilling and hammer drilling modes. This flexibility makes it suitable for a range of tasks, from simple household repairs to more complex construction projects. The hammer function, in particular, excels when drilling into hard surfaces like concrete or masonry, making it a valuable tool for contractors and construction workers.

Another key characteristic of the H450IS is its ergonomic design. The tool is equipped with a comfortable grip and a lightweight body, which reduces user fatigue during extended periods of work. Additionally, the integrated side handle provides added control and stability, ensuring accurate drilling and driving.

For improved performance, the H450IS uses advanced technologies such as an automatic clutch system, which helps prevent over-tightening of screws and reduces damage to materials. This feature enhances the longevity of both the tool and the workpiece, making it a reliable choice for professionals who require consistent results.

The durable construction of the H450IS is another highlight, featuring a robust housing that withstands job site conditions. This ensures that the drill remains in peak operational condition even after frequent use in demanding environments.

Overall, the Porter-Cable H450IS is a well-rounded hammer drill that offers a potent combination of power, versatility, and user-friendly features. Its various modes, comfortable design, and reliable performance make it an invaluable addition to any toolbox, whether for professional contractors or aspiring DIYers looking to tackle their next project with confidence.
Top Page Image Contents