Porter-Cable H450IS instruction manual Storage, Engine Preparation, Generator

Page 18

STORAGE

If you are going to store your generator for more than 30 days, use the following information as a guide to prepare the generator for storage.

Never store generator with fuel in the tank indoors or in enclosed, poorly ventilated areas, where fumes can reach

an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or other gas appliances.

ENGINE PREPARATION

1.Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage.

2.Run engine at least 10 minutes after adding stabilizer to allow it to enter the fuel system.

3.Next shut off engine.

4.Disconnect the spark plug wire and remove the spark plug.

5.Add one teaspoon of oil through the spark plug hole.

6.Place rag over spark plug hole and pull the recoil a few times to lubricate the combustion chamber.

7.Replace the spark plug, but do not connect the spark plug wire.

NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine.

GENERATOR

•Clean the generator as outlined in the Maintenance Section on this manual.

•Check that cooling air slots and openings on generator are open and unobstructed.

D28512

18- ENG

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Generator Important Safety Instructions Safety Guidelines / DefinitionsConsumer Safety Information Risk of Electrocution and FireBe used When installing a DoubleRisk of Electrocution and Fire OperationRisk of Fire Unit Indoors or in ANYConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe Operation Risk of HOT Surfaces Risk of Moving PartsRisk from Lifting Read and understand all safety warnings Consumer General and Service InformationSpecifications H450ISOther Loose Parts AssemblyRemove Generator from Carton Grounding the GeneratorObtaining Electricity from the Generator Double Throw Transfer SwitchExtension Cord Wire Gauge Chart Length Size Amperage Extension CordsAssemble Skyhook Tools neededParts bag contains Operation Know Your GeneratorIdle Control Choose the correct applicationTo Start the Engine Deadly gasConnecting Electrical Loads Stopping EngineConnecting Procedure for Raising or Suspending Generator Maintenance Storage Engine PreparationGenerator Wattage Calculations Determining Wattage RequirementsRunning Watts Starting Watts Starting Wattage Requirements Volts X Amp = Watts Example 120 volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserQuick Facts

H450IS specifications

The Porter-Cable H450IS is a high-performance, lightweight electric hammer drill designed to meet the needs of both professionals and DIY enthusiasts. Renowned for its versatility and durability, the H450IS is ideal for various applications including drilling in wood, metal, and masonry, as well as for driving screws efficiently.

One of the standout features of the H450IS is its powerful motor that delivers an impressive amount of torque, making it capable of handling tough materials with ease. The tool boasts a variable speed trigger, allowing users to control the speed for precise drilling. This feature is especially beneficial when working with delicate materials that require a gentler touch.

The H450IS is equipped with a dual-mode operation, allowing users to switch between rotary drilling and hammer drilling modes. This flexibility makes it suitable for a range of tasks, from simple household repairs to more complex construction projects. The hammer function, in particular, excels when drilling into hard surfaces like concrete or masonry, making it a valuable tool for contractors and construction workers.

Another key characteristic of the H450IS is its ergonomic design. The tool is equipped with a comfortable grip and a lightweight body, which reduces user fatigue during extended periods of work. Additionally, the integrated side handle provides added control and stability, ensuring accurate drilling and driving.

For improved performance, the H450IS uses advanced technologies such as an automatic clutch system, which helps prevent over-tightening of screws and reduces damage to materials. This feature enhances the longevity of both the tool and the workpiece, making it a reliable choice for professionals who require consistent results.

The durable construction of the H450IS is another highlight, featuring a robust housing that withstands job site conditions. This ensures that the drill remains in peak operational condition even after frequent use in demanding environments.

Overall, the Porter-Cable H450IS is a well-rounded hammer drill that offers a potent combination of power, versatility, and user-friendly features. Its various modes, comfortable design, and reliable performance make it an invaluable addition to any toolbox, whether for professional contractors or aspiring DIYers looking to tackle their next project with confidence.
Top Page Image Contents