Powermate P-WB-163150-[E] Engine Preparation, Engine Oil, Ambient Service Temperature

Page 8

Engine Preparation

• Save all instructions

A Engine Oil

CAUTION

Engine shipped without oil. Failure to add oil will result in serious engine damage.

A bottle of SAE 30 engine oil is included with your blower. Refer to the chart on the right for alternative oil types to use at different temperatures. Always use a high quality detergent oil classified “For Service, SG, SH, SJ” or higher. Do not use special additives.

CAUTION

Always use recommended oil type. Using dirty oil or incorrect oil type such as 2-stroke engine oil will shorten engine life.

NOTE: Engine Oil Capacity is 562 ml. For first time fill, simply add the entire contents of the provided oil bottle to the crankcase.

SAE

SAE 10W-30

 

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEMP -20

0

20

40

60

80

 

100° F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-30

 

-20

-10

0

10

20

30 40° C

 

 

 

 

Ambient Service Temperature

 

 

 

 

HOW TO CHECK OIL LEVEL AND FILL TO PROPER LEVEL

WARNING

Before checking oil, make sure engine is off, and spark plug wire has been disconnected from spark plug.

1.Set walk behind blower on a level surface.

2.Remove the oil fill cap/dipstick and wipe clean with cloth.

(See Figure 3)

3.Insert dipstick into fill spout but do NOT screw in.

Remove dipstick and check oil level.

4.When oil level is full, the oil will be at upper limit on dip stick. If oil level is near or below the lower limit, oil must be added. (See Figure 4)

5.Add oil slowly until the oil level reaches the upper limit of the dipstick. Use a funnel or nozzle to reduce spillage.

CAUTION

Frequently check oil level while filling. DO NOT OVERFILL. DO NOT UNDERFILL. Running engine at improper oil level will seriously damage engine.

6. Replace and tighten dipstick.

7. Clean up any spilled oil.

Upper Limit

Lower Limit

Fuel Tank Cap

Oil Fill Cap/

Dipstick

Figure 3

Oil Fill Cap/

Dipstick

Figure 4

Questions? Call Toll Free at 1-800-737-2112

7

Copyright © 2009 MAT Engine Technologies, LLC

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Cyclone Walk Behind Blower Operator’s ManualSafety Definitions Safety Warning SymbolsControl and Operating Symbols Questions? Call Toll Free atImportant Safety Information Preparation SafetyOperation Safety Save all instructionsSave all instructions Operation Safety Fuel SafetyStorage Safety REPAIR, MAINTENANCE, and Adjustment SafetyChildren Safety Specifications Parts & FeaturesToll Free AssemblyHow to Remove Blower from Carton Engine Oil Ambient Service TemperatureEngine Preparation Before Starting the Engine OperationFuel How to Start Engine How to Stop the Blower How to Adjust the Vertical Flow AngleHow to Redirect Air Flow toward the Front Operation Save all instructionsTips for Using your Walk Behind Blower Service MaintenanceService Records How to Change the Engine Oil How to Clean the Air FilterSpark Plug Model Torch F7RTC How to Check the Spark PlugHow to Prepare for Storage Technical Service If you need assistance or have any questions, Call Toll FreeTroubleshooting Problem Possible Causes SolutionsWarranty Powermate Walk Behind Blower Limited WarrantyWarranty Save all instructions Emisson Control System WarrantyYour Warranty Rightes and Obligations Manufacturer’s Warranty CoverageWarranty How to Obtain Warranty ServiceExclusions Limitations of LiabilitySystems Covered by this Warranty Parts Description Questions? Call Toll Free at Conserve Este Manual Como Referencia Definiciones de seguridad Símbolos de alerta para sequradadSímbolos de advertencia para seguridad Símbolos de control y funcionamientoInstrucciones de seguridad importantes Conserve todas las instruccionesResponsabilidad DEL Usuario Seguridad durante la preparaciónInstrucciones de seguridad importantes la siguiente Seguridad DEL CombustibleSeguridad DE Niños Seguridad DE AlmacenamientoREPARACIÓN, Mantenimiento Y Seguridad DE Ajuste Copyright 2009 MAT Engine Technologies, LLC EspecificacionesPiezas y características Cómo montar el asidero MontajeCómo sacar el soplador de la caja Preparción del motor Aceite de motorPreparción del motor la siguiente UsoCombustible Antes de arrancar el motorAntes de arrancar el motor la siguiente Cómo arrancar el motorUso la siguiente Cómo ajustar el ángulo de caudal verticalUso la siguiente Conserve todas las instrucciones Consejos Para BordearMantenimiento Programa de mantenimientoCómo limpiar al filtro de aire Mantenimiento la siguienteCómo cambiar el aceite del motor Modelo de bujía Torch F7RTC Cómo preparala para almacenamientoSi necesita ayuda o tiene una duda Llame SIN Costo AL Servicio técnicoWildlife Way Long Grove, IL Diagnóstico y resolución de problemas Problema Causas Posibles SolucionesPowermate Soplador de operación a pie Limited Warranty GarantíaGarantía la siguiente Conserve todas las instrucciones Garantía del sistema pro control de emisiones contaminantesDerechos y obligaciones al amparo de la garantía Cobertura de la garantía del fabricanteCobertura de la garantía Cómo obtener servicio de garantíaExclusiones Limitación de responsabilidadGarantía la siguiente Llame sin costo al

P-WB-163150, P-WB-163150-[E] specifications

The Powermate P-WB-163150-[E],P-WB-163150 is a high-performance water-based air compressor designed to meet the needs of various applications, including professional and DIY projects. This versatile compressor stands out due to its robust construction and innovative features, making it an essential tool for both contractors and hobbyists.

One of the primary features of the Powermate P-WB-163150 is its powerful motor, providing a reliable source of compressed air for numerous tasks. With a maximum pressure of up to 150 PSI, it can easily handle heavy-duty applications like spray painting, inflating tires, or operating pneumatic tools. This wide pressure range gives users the flexibility to adapt the compressor for different tools and projects, ensuring optimal performance.

The compressor's water-based technology is another highlight, setting it apart from traditional oil-based compressors. This innovative design not only contributes to a more environmentally friendly operation but also minimizes maintenance requirements. Users can enjoy lower operating costs and less hassle, as there is no need for regular oil changes. This feature enhances the overall user experience, allowing for longer work periods without interruptions.

Additionally, the Powermate P-WB-163150 features a compact and portable design, equipped with a sturdy handle and wheels for easy transport. This mobility ensures that users can take the compressor to various job sites or store it conveniently when not in use. Its lightweight construction does not compromise durability, as the materials used are designed to withstand the rigors of frequent use.

Another key characteristic of this model is its noise reduction technology. The compressor operates at a reduced noise level, making it suitable for residential areas where excessive noise could be an issue. This feature is particularly beneficial for users who require an efficient compressor without disturbing the neighbors.

With user-friendly controls, the Powermate P-WB-163150 is designed for ease of use. The intuitive interface and clear gauges allow users to monitor pressure levels effortlessly, ensuring a smooth operation. Combined with safety features like thermal overload protection, this compressor prioritizes user safety while enhancing operational efficiency.

In summary, the Powermate P-WB-163150-[E],P-WB-163150 offers a perfect blend of power, portability, and user-friendly design, making it an ideal choice for anyone in need of a reliable air compressor. Its water-based technology, robust construction, and innovative features cater to a wide range of applications while ensuring a seamless user experience.
Top Page Image Contents