Poulan 183384 Transaxle Gear Shift Lever Neutral Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

 

 

ADJUSTMENT

 

BOLT

FIG. 23

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsi- bilities section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FIG. 25

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PR17542STC IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled HardwareSeat Keys Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMulching Mowing Tips Service Dates General Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower see FIGTo Remove Mower see FIG FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor - Model Number PR17542STC, Product Number 954 56 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Wheels and Tires DecalsEngine 170771 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line DegreeParts and Service

183384 specifications

The Poulan 183384 is a robust, high-performance chainsaw that is designed for both professional and home-use applications. It stands out in the market due to its combination of power, durability, and user-friendly features that make it an ideal choice for a variety of cutting tasks, from trimming shrubs to felling larger trees.

One of the main features of the Poulan 183384 is its powerful engine. Equipped with a reliable two-stroke engine, this chainsaw delivers ample power to handle demanding cutting jobs with ease. The high engine speed ensures fast cutting performance, reducing the time needed for each job and making it an efficient tool for both casual users and seasoned professionals.

In terms of design, the Poulan 183384 boasts an ergonomic build that prioritizes user comfort. The handles are designed for a secure grip, which enhances control and reduces fatigue during extended periods of use. Additionally, its lightweight construction makes it easy to maneuver, allowing for better handling and precision while cutting.

Safety features are crucial in chainsaw operation, and the Poulan 183384 does not disappoint. It is equipped with a chain brake that instantly stops the chain rotation in the event of kickback, minimizing the risk of accidents. The chainsaw also features an adjustable oil pump, which allows users to control the amount of oil distributed to the chain, ensuring optimal lubrication and extending the life of both the chain and the bar.

The innovative anti-vibration technology integrated into the Poulan 183384 minimizes vibrations during operation, enhancing user comfort and control. This technology is particularly beneficial for users who need to work for extended periods, as it helps reduce strain on the hands and arms, ultimately making the task more enjoyable.

Maintenance is made easy with the Poulan 183384, as it features a tool-less chain tensioning system. This allows users to adjust the chain tension quickly and without the need for additional tools, ensuring that the chainsaw is always ready for optimal performance.

Overall, the Poulan 183384 stands as a reliable, efficient, and user-friendly option for anyone in need of a powerful chainsaw. Whether for professional landscaping, forestry work, or simply maintaining a home garden, it is equipped to handle a wide variety of tasks with precision and ease.
Top Page Image Contents