Poulan 183384 owner manual When operator leaves

Page 26

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PR17542STC General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Seat Unassembled HardwareSteering Wheel Keys Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mulching Mowing Tips Mowing TipsTo Start Engine See Fig Customer Responsibilities General Recommendations Lubrication ChartService Dates Before Each USETractor Engine Muffler CleaningEngine OIL Filter Spark PlugsTo Remove Mower see FIG Service and AdjustmentsTo Install Mower see FIG To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PR17542STC, Product Number 954 56Electrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Decals Wheels and TiresEngine 170771 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183384 specifications

The Poulan 183384 is a robust, high-performance chainsaw that is designed for both professional and home-use applications. It stands out in the market due to its combination of power, durability, and user-friendly features that make it an ideal choice for a variety of cutting tasks, from trimming shrubs to felling larger trees.

One of the main features of the Poulan 183384 is its powerful engine. Equipped with a reliable two-stroke engine, this chainsaw delivers ample power to handle demanding cutting jobs with ease. The high engine speed ensures fast cutting performance, reducing the time needed for each job and making it an efficient tool for both casual users and seasoned professionals.

In terms of design, the Poulan 183384 boasts an ergonomic build that prioritizes user comfort. The handles are designed for a secure grip, which enhances control and reduces fatigue during extended periods of use. Additionally, its lightweight construction makes it easy to maneuver, allowing for better handling and precision while cutting.

Safety features are crucial in chainsaw operation, and the Poulan 183384 does not disappoint. It is equipped with a chain brake that instantly stops the chain rotation in the event of kickback, minimizing the risk of accidents. The chainsaw also features an adjustable oil pump, which allows users to control the amount of oil distributed to the chain, ensuring optimal lubrication and extending the life of both the chain and the bar.

The innovative anti-vibration technology integrated into the Poulan 183384 minimizes vibrations during operation, enhancing user comfort and control. This technology is particularly beneficial for users who need to work for extended periods, as it helps reduce strain on the hands and arms, ultimately making the task more enjoyable.

Maintenance is made easy with the Poulan 183384, as it features a tool-less chain tensioning system. This allows users to adjust the chain tension quickly and without the need for additional tools, ensuring that the chainsaw is always ready for optimal performance.

Overall, the Poulan 183384 stands as a reliable, efficient, and user-friendly option for anyone in need of a powerful chainsaw. Whether for professional landscaping, forestry work, or simply maintaining a home garden, it is equipped to handle a wide variety of tasks with precision and ease.
Top Page Image Contents