Poulan 183384 owner manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Utility knife

(1)

3/4" wrench

Tire pressure gauge

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 1/2 hex nut and tighten se- curely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

STEERING

WHEEL INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING BOOT

TABS

EXTENSION

SHAFT

ADAPTER

1/4 HEX BOLT

 

1/4 LOCKNUT

LOWER

TAB

STEERING

SLOTS

SHAFT

 

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

Lift seat pan to raised position.

If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

6

Image 6
Contents PR17542STC General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Seat Unassembled HardwareSteering Wheel Keys Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMulching Mowing Tips Customer Responsibilities General Recommendations Lubrication ChartService Dates Before Each USETractor Engine Muffler CleaningEngine OIL Filter Spark PlugsService and Adjustments To Install Mower see FIGTo Remove Mower see FIG To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigsTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PR17542STC, Product Number 954 56Electrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Adaptor Wheel Strg Seat Assembly Decals Wheels and TiresEngine 170771 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Limited Warranty Policy Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183384 specifications

The Poulan 183384 is a robust, high-performance chainsaw that is designed for both professional and home-use applications. It stands out in the market due to its combination of power, durability, and user-friendly features that make it an ideal choice for a variety of cutting tasks, from trimming shrubs to felling larger trees.

One of the main features of the Poulan 183384 is its powerful engine. Equipped with a reliable two-stroke engine, this chainsaw delivers ample power to handle demanding cutting jobs with ease. The high engine speed ensures fast cutting performance, reducing the time needed for each job and making it an efficient tool for both casual users and seasoned professionals.

In terms of design, the Poulan 183384 boasts an ergonomic build that prioritizes user comfort. The handles are designed for a secure grip, which enhances control and reduces fatigue during extended periods of use. Additionally, its lightweight construction makes it easy to maneuver, allowing for better handling and precision while cutting.

Safety features are crucial in chainsaw operation, and the Poulan 183384 does not disappoint. It is equipped with a chain brake that instantly stops the chain rotation in the event of kickback, minimizing the risk of accidents. The chainsaw also features an adjustable oil pump, which allows users to control the amount of oil distributed to the chain, ensuring optimal lubrication and extending the life of both the chain and the bar.

The innovative anti-vibration technology integrated into the Poulan 183384 minimizes vibrations during operation, enhancing user comfort and control. This technology is particularly beneficial for users who need to work for extended periods, as it helps reduce strain on the hands and arms, ultimately making the task more enjoyable.

Maintenance is made easy with the Poulan 183384, as it features a tool-less chain tensioning system. This allows users to adjust the chain tension quickly and without the need for additional tools, ensuring that the chainsaw is always ready for optimal performance.

Overall, the Poulan 183384 stands as a reliable, efficient, and user-friendly option for anyone in need of a powerful chainsaw. Whether for professional landscaping, forestry work, or simply maintaining a home garden, it is equipped to handle a wide variety of tasks with precision and ease.