Poulan 195620 manual Cleaning

Page 18

MAINTENANCE

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

•Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.Tighten cap onto the tube securely when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

AIR FILTER

Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 13)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

FUEL FILTER

FIG. 13

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HD21H42 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195620 specifications

The Poulan 195620 is a versatile and powerful chainsaw designed for homeowners and outdoor enthusiasts who need a reliable tool for cutting firewood, clearing brush, and performing general yard maintenance. Known for its robust performance and user-friendly features, the Poulan 195620 stands out in the market for its combination of power, efficiency, and ease of use.

One of the main features of the Poulan 195620 is its 20-inch cutting bar, which allows for large cutting capacities, making it suitable for tackling bigger logs and branches. The chainsaw is powered by a durable 50cc two-stroke engine that delivers consistent power and performance, ensuring that users can complete their tasks efficiently. With a maximum chain speed of 7,000 RPM, the Poulan 195620 cuts through wood with speed and precision.

The chainsaw utilizes an automatic oiling system that keeps the chain lubricated during operation, reducing friction and wear while enhancing cutting performance. This feature not only extends the life of the chain but also ensures a smoother, more efficient cutting experience, allowing users to spend more time working and less time on maintenance.

Another important aspect of the Poulan 195620 is its ergonomic design, which includes a comfortable handle that reduces vibration and enhances grip. This design consideration is essential for prolonged use, as it minimizes user fatigue and allows for greater control during cutting tasks. The chainsaw also includes easy access to the air filter and spark plug, simplifying routine maintenance and keeping the unit running at peak performance.

In terms of safety, the Poulan 195620 is equipped with several features designed to protect the user. The chainsaw has a chain brake that stops the chain's movement quickly in the event of kickback, while hand guards provide additional safety during operation. Furthermore, the easy-start ignition system helps users start the engine with minimal effort, reducing frustration and ensuring that the chainsaw can be readied for use without delay.

Overall, the Poulan 195620 is an excellent choice for those seeking a reliable and efficient chainsaw. Its combination of power, ergonomic design, and safety features make it a standout option for anyone looking to tackle outdoor projects with confidence and ease. Whether you are a seasoned professional or a casual user, the Poulan 195620 offers the performance and reliability to meet your cutting needs.
Top Page Image Contents