Poulan 195620 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(1)

1/2" wrench

Tire pressure gauge

 

 

Utility knife

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

STEERING WHEEL

LARGE FLAT WASHER

STEERING

BOOT

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment knob securely.

6

Image 6
Contents HD21H42 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195620 specifications

The Poulan 195620 is a versatile and powerful chainsaw designed for homeowners and outdoor enthusiasts who need a reliable tool for cutting firewood, clearing brush, and performing general yard maintenance. Known for its robust performance and user-friendly features, the Poulan 195620 stands out in the market for its combination of power, efficiency, and ease of use.

One of the main features of the Poulan 195620 is its 20-inch cutting bar, which allows for large cutting capacities, making it suitable for tackling bigger logs and branches. The chainsaw is powered by a durable 50cc two-stroke engine that delivers consistent power and performance, ensuring that users can complete their tasks efficiently. With a maximum chain speed of 7,000 RPM, the Poulan 195620 cuts through wood with speed and precision.

The chainsaw utilizes an automatic oiling system that keeps the chain lubricated during operation, reducing friction and wear while enhancing cutting performance. This feature not only extends the life of the chain but also ensures a smoother, more efficient cutting experience, allowing users to spend more time working and less time on maintenance.

Another important aspect of the Poulan 195620 is its ergonomic design, which includes a comfortable handle that reduces vibration and enhances grip. This design consideration is essential for prolonged use, as it minimizes user fatigue and allows for greater control during cutting tasks. The chainsaw also includes easy access to the air filter and spark plug, simplifying routine maintenance and keeping the unit running at peak performance.

In terms of safety, the Poulan 195620 is equipped with several features designed to protect the user. The chainsaw has a chain brake that stops the chain's movement quickly in the event of kickback, while hand guards provide additional safety during operation. Furthermore, the easy-start ignition system helps users start the engine with minimal effort, reducing frustration and ensuring that the chainsaw can be readied for use without delay.

Overall, the Poulan 195620 is an excellent choice for those seeking a reliable and efficient chainsaw. Its combination of power, ergonomic design, and safety features make it a standout option for anyone looking to tackle outdoor projects with confidence and ease. Whether you are a seasoned professional or a casual user, the Poulan 195620 offers the performance and reliability to meet your cutting needs.