Poulan 195620 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 22

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 24

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents HD21H42 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195620 specifications

The Poulan 195620 is a versatile and powerful chainsaw designed for homeowners and outdoor enthusiasts who need a reliable tool for cutting firewood, clearing brush, and performing general yard maintenance. Known for its robust performance and user-friendly features, the Poulan 195620 stands out in the market for its combination of power, efficiency, and ease of use.

One of the main features of the Poulan 195620 is its 20-inch cutting bar, which allows for large cutting capacities, making it suitable for tackling bigger logs and branches. The chainsaw is powered by a durable 50cc two-stroke engine that delivers consistent power and performance, ensuring that users can complete their tasks efficiently. With a maximum chain speed of 7,000 RPM, the Poulan 195620 cuts through wood with speed and precision.

The chainsaw utilizes an automatic oiling system that keeps the chain lubricated during operation, reducing friction and wear while enhancing cutting performance. This feature not only extends the life of the chain but also ensures a smoother, more efficient cutting experience, allowing users to spend more time working and less time on maintenance.

Another important aspect of the Poulan 195620 is its ergonomic design, which includes a comfortable handle that reduces vibration and enhances grip. This design consideration is essential for prolonged use, as it minimizes user fatigue and allows for greater control during cutting tasks. The chainsaw also includes easy access to the air filter and spark plug, simplifying routine maintenance and keeping the unit running at peak performance.

In terms of safety, the Poulan 195620 is equipped with several features designed to protect the user. The chainsaw has a chain brake that stops the chain's movement quickly in the event of kickback, while hand guards provide additional safety during operation. Furthermore, the easy-start ignition system helps users start the engine with minimal effort, reducing frustration and ensuring that the chainsaw can be readied for use without delay.

Overall, the Poulan 195620 is an excellent choice for those seeking a reliable and efficient chainsaw. Its combination of power, ergonomic design, and safety features make it a standout option for anyone looking to tackle outdoor projects with confidence and ease. Whether you are a seasoned professional or a casual user, the Poulan 195620 offers the performance and reliability to meet your cutting needs.
Top Page Image Contents