Poulan 195620 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents HD21H42 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195620 specifications

The Poulan 195620 is a versatile and powerful chainsaw designed for homeowners and outdoor enthusiasts who need a reliable tool for cutting firewood, clearing brush, and performing general yard maintenance. Known for its robust performance and user-friendly features, the Poulan 195620 stands out in the market for its combination of power, efficiency, and ease of use.

One of the main features of the Poulan 195620 is its 20-inch cutting bar, which allows for large cutting capacities, making it suitable for tackling bigger logs and branches. The chainsaw is powered by a durable 50cc two-stroke engine that delivers consistent power and performance, ensuring that users can complete their tasks efficiently. With a maximum chain speed of 7,000 RPM, the Poulan 195620 cuts through wood with speed and precision.

The chainsaw utilizes an automatic oiling system that keeps the chain lubricated during operation, reducing friction and wear while enhancing cutting performance. This feature not only extends the life of the chain but also ensures a smoother, more efficient cutting experience, allowing users to spend more time working and less time on maintenance.

Another important aspect of the Poulan 195620 is its ergonomic design, which includes a comfortable handle that reduces vibration and enhances grip. This design consideration is essential for prolonged use, as it minimizes user fatigue and allows for greater control during cutting tasks. The chainsaw also includes easy access to the air filter and spark plug, simplifying routine maintenance and keeping the unit running at peak performance.

In terms of safety, the Poulan 195620 is equipped with several features designed to protect the user. The chainsaw has a chain brake that stops the chain's movement quickly in the event of kickback, while hand guards provide additional safety during operation. Furthermore, the easy-start ignition system helps users start the engine with minimal effort, reducing frustration and ensuring that the chainsaw can be readied for use without delay.

Overall, the Poulan 195620 is an excellent choice for those seeking a reliable and efficient chainsaw. Its combination of power, ergonomic design, and safety features make it a standout option for anyone looking to tackle outdoor projects with confidence and ease. Whether you are a seasoned professional or a casual user, the Poulan 195620 offers the performance and reliability to meet your cutting needs.
Top Page Image Contents