Poulan 195620 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 14)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 14)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

 

SMALL RETAINER SPRING

 

 

 

 

CLUTCH SPRING

 

 

 

 

FLAT WASHER

 

 

SQUARE HOLE

SMALL RETAINER SPRING

 

SUSPENSION

ENGINE PULLEY

 

 

 

ARMS

 

 

 

 

CLUTCH SPRING

 

 

 

 

 

 

 

FRONT LINK

RETAINER SPRING

 

 

 

 

ANTI-SWAY BAR

 

 

 

 

 

 

 

 

RETAINER SPRINGS

COLLAR

 

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE RETAINER

 

 

 

SPRING

BRACKET

 

DEFLECTOR SHIELD

 

 

 

 

 

 

 

FIG. 14

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation HD21H42II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195620 specifications

The Poulan 195620 is a versatile and powerful chainsaw designed for homeowners and outdoor enthusiasts who need a reliable tool for cutting firewood, clearing brush, and performing general yard maintenance. Known for its robust performance and user-friendly features, the Poulan 195620 stands out in the market for its combination of power, efficiency, and ease of use.

One of the main features of the Poulan 195620 is its 20-inch cutting bar, which allows for large cutting capacities, making it suitable for tackling bigger logs and branches. The chainsaw is powered by a durable 50cc two-stroke engine that delivers consistent power and performance, ensuring that users can complete their tasks efficiently. With a maximum chain speed of 7,000 RPM, the Poulan 195620 cuts through wood with speed and precision.

The chainsaw utilizes an automatic oiling system that keeps the chain lubricated during operation, reducing friction and wear while enhancing cutting performance. This feature not only extends the life of the chain but also ensures a smoother, more efficient cutting experience, allowing users to spend more time working and less time on maintenance.

Another important aspect of the Poulan 195620 is its ergonomic design, which includes a comfortable handle that reduces vibration and enhances grip. This design consideration is essential for prolonged use, as it minimizes user fatigue and allows for greater control during cutting tasks. The chainsaw also includes easy access to the air filter and spark plug, simplifying routine maintenance and keeping the unit running at peak performance.

In terms of safety, the Poulan 195620 is equipped with several features designed to protect the user. The chainsaw has a chain brake that stops the chain's movement quickly in the event of kickback, while hand guards provide additional safety during operation. Furthermore, the easy-start ignition system helps users start the engine with minimal effort, reducing frustration and ensuring that the chainsaw can be readied for use without delay.

Overall, the Poulan 195620 is an excellent choice for those seeking a reliable and efficient chainsaw. Its combination of power, ergonomic design, and safety features make it a standout option for anyone looking to tackle outdoor projects with confidence and ease. Whether you are a seasoned professional or a casual user, the Poulan 195620 offers the performance and reliability to meet your cutting needs.
Top Page Image Contents