Poulan 411229 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 15)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Roll belt off engine pulley (M) and belt keepers (G).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE

MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 16–19)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

G M F

Q RG

A E

B

P C

K

L D

FIG. 15

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents PB19546LT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Carton AssemblyTools Required for Assembly To Remove Tractor fromCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig Before Starting the Engine Mowing Tips General Recommendations MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Precision SIDE-TO-SIDE AdjustmentTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Tractor - Model Number PB19546LT 96042003500, Product no 42 SchematicElectrical KEY Part Description 162 DriveRepair Parts Chassis 194263 Drawbar Wheels and Tires Steering Optional Equipment EngineEngine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPolicy

411229 specifications

The Poulan 411229 is a robust and versatile chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its efficiency and reliability, this chainsaw stands out in a crowded market thanks to its advanced features and user-friendly design.

One of the main highlights of the Poulan 411229 is its powerful engine. Equipped with a high-performance gas engine, this chainsaw delivers impressive power that allows for efficient cutting through various types of wood, whether you are tackling thick tree trunks or lighter branches. The engine is designed to minimize exhaust emissions, aligning with modern environmental standards, making it a responsible choice for users who are conscious about their ecological footprint.

The Poulan 411229 features a high-quality bar and chain system. The saw comes with a durable bar that provides excellent cutting capacity while maintaining stability. The chain is engineered for optimal performance, ensuring smooth cutting and longer-lasting sharpness, meaning less time spent on maintenance and more time getting the job done.

An essential aspect of the design is the user comfort it offers. The chainsaw is equipped with an anti-vibration system that significantly reduces operator fatigue during prolonged use. This feature is particularly beneficial for professional arborists and landscapers who depend on their tools for extended periods.

Safety is another priority in the design of the Poulan 411229. The chainsaw includes reliable safety features such as a chain brake that stops the chain in the event of kickback, and a safety throttle that prevents accidental starting. These features are designed to give users peace of mind while operating the tool.

Furthermore, the Poulan 411229 has an easy-start mechanism that simplifies the ignition process. This is particularly advantageous for less experienced users who may struggle with traditional starting methods. The chainsaw also has a tool-less chain tensioning system, allowing for quick adjustments to the chain without the need for additional tools, fostering both convenience and efficiency in operation.

In summary, the Poulan 411229 is a reliable, efficient, and user-friendly chainsaw. Its powerful engine, durable bar and chain, user comfort features, and safety enhancements make it an excellent choice for anyone looking to tackle cutting tasks with confidence and ease. Whether for professional use or weekend projects, this chainsaw represents a smart investment in quality and performance.
Top Page Image Contents