Poulan 411229 manual To Level Mower, Precision SIDE-TO-SIDE Adjustment

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig .20)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

NOTE: As desired, you can raise the low side of mower or lower the high side.

•Go to side of mower you wish to adjust.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower the mower, or, to the right to raise the mower.

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

FIG. 20

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

•If adjustment is necessary, see steps in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

 

02966

A

A

FIG. 21

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

02548

BB

FIG. 22

B

A

Tighten adjust nut

Loosen adjust nut

B to raise mower

B to lower mower

02950

Loosen jam nut A first

FIG. 23

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten

21 jam nut securely against adjustment nut.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents PB19546LT Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from CartonCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig Before Starting the Engine Mowing Tips General Recommendations MaintenanceTractor Blade Removal See FigTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Precision SIDE-TO-SIDE AdjustmentTo Replace Mower Drive Belt See Fig Belt InstallationTo Replace Motion Belt Drive See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Tractor - Model Number PB19546LT 96042003500, Product no 42 SchematicElectrical KEY Part Description 162 DriveRepair Parts Chassis 194263 Drawbar Wheels and Tires Steering Optional Equipment EngineEngine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPolicy

411229 specifications

The Poulan 411229 is a robust and versatile chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its efficiency and reliability, this chainsaw stands out in a crowded market thanks to its advanced features and user-friendly design.

One of the main highlights of the Poulan 411229 is its powerful engine. Equipped with a high-performance gas engine, this chainsaw delivers impressive power that allows for efficient cutting through various types of wood, whether you are tackling thick tree trunks or lighter branches. The engine is designed to minimize exhaust emissions, aligning with modern environmental standards, making it a responsible choice for users who are conscious about their ecological footprint.

The Poulan 411229 features a high-quality bar and chain system. The saw comes with a durable bar that provides excellent cutting capacity while maintaining stability. The chain is engineered for optimal performance, ensuring smooth cutting and longer-lasting sharpness, meaning less time spent on maintenance and more time getting the job done.

An essential aspect of the design is the user comfort it offers. The chainsaw is equipped with an anti-vibration system that significantly reduces operator fatigue during prolonged use. This feature is particularly beneficial for professional arborists and landscapers who depend on their tools for extended periods.

Safety is another priority in the design of the Poulan 411229. The chainsaw includes reliable safety features such as a chain brake that stops the chain in the event of kickback, and a safety throttle that prevents accidental starting. These features are designed to give users peace of mind while operating the tool.

Furthermore, the Poulan 411229 has an easy-start mechanism that simplifies the ignition process. This is particularly advantageous for less experienced users who may struggle with traditional starting methods. The chainsaw also has a tool-less chain tensioning system, allowing for quick adjustments to the chain without the need for additional tools, fostering both convenience and efficiency in operation.

In summary, the Poulan 411229 is a reliable, efficient, and user-friendly chainsaw. Its powerful engine, durable bar and chain, user comfort features, and safety enhancements make it an excellent choice for anyone looking to tackle cutting tasks with confidence and ease. Whether for professional use or weekend projects, this chainsaw represents a smart investment in quality and performance.
Top Page Image Contents