Poulan 411229 Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig, Front Wheel TOE-IN/CAMBER

Page 23

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

GEARSHIFT LEVER

NEUTRAL LOCK GATE

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and

corrosion.23

FIG. 28

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PB19546LT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Carton AssemblyTools Required for Assembly To Remove Tractor fromCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS Before Starting the Engine Mowing Tips General Recommendations MaintenanceTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Precision SIDE-TO-SIDE AdjustmentTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Tractor - Model Number PB19546LT 96042003500, Product no 42 SchematicElectrical KEY Part Description 162 DriveRepair Parts Chassis 194263 Drawbar Wheels and Tires Steering Optional Equipment EngineEngine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPolicy

411229 specifications

The Poulan 411229 is a robust and versatile chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its efficiency and reliability, this chainsaw stands out in a crowded market thanks to its advanced features and user-friendly design.

One of the main highlights of the Poulan 411229 is its powerful engine. Equipped with a high-performance gas engine, this chainsaw delivers impressive power that allows for efficient cutting through various types of wood, whether you are tackling thick tree trunks or lighter branches. The engine is designed to minimize exhaust emissions, aligning with modern environmental standards, making it a responsible choice for users who are conscious about their ecological footprint.

The Poulan 411229 features a high-quality bar and chain system. The saw comes with a durable bar that provides excellent cutting capacity while maintaining stability. The chain is engineered for optimal performance, ensuring smooth cutting and longer-lasting sharpness, meaning less time spent on maintenance and more time getting the job done.

An essential aspect of the design is the user comfort it offers. The chainsaw is equipped with an anti-vibration system that significantly reduces operator fatigue during prolonged use. This feature is particularly beneficial for professional arborists and landscapers who depend on their tools for extended periods.

Safety is another priority in the design of the Poulan 411229. The chainsaw includes reliable safety features such as a chain brake that stops the chain in the event of kickback, and a safety throttle that prevents accidental starting. These features are designed to give users peace of mind while operating the tool.

Furthermore, the Poulan 411229 has an easy-start mechanism that simplifies the ignition process. This is particularly advantageous for less experienced users who may struggle with traditional starting methods. The chainsaw also has a tool-less chain tensioning system, allowing for quick adjustments to the chain without the need for additional tools, fostering both convenience and efficiency in operation.

In summary, the Poulan 411229 is a reliable, efficient, and user-friendly chainsaw. Its powerful engine, durable bar and chain, user comfort features, and safety enhancements make it an excellent choice for anyone looking to tackle cutting tasks with confidence and ease. Whether for professional use or weekend projects, this chainsaw represents a smart investment in quality and performance.
Top Page Image Contents