Poulan 411229 manual Check Battery See Fig

Page 7

ASSEMBLY

•Push down on seat to engage pads in slots and pull seat towards rear of tractor.

•Raise seat and tighten bolt securely.

•Remove tape and discard.

•Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT

 

TAPE

PAD

 

 

FLAT

 

 

WASHER

 

 

SEAT PAN

 

BOLT

TAB

ADJUSTMENT

HANDLE

 

 

Fig. 3

CHECK BATTERY (See Fig. 4)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

FIG. 4

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this man- ual). After engine has started, move throttle control to idle (slow) position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PB19546LT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Carton AssemblyTools Required for Assembly To Remove Tractor fromCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig Before Starting the Engine Mowing Tips General Recommendations MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Precision SIDE-TO-SIDE AdjustmentTo Check Brake Belt InstallationTo Replace Mower Drive Belt See Fig To Replace Motion Belt Drive See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Tractor - Model Number PB19546LT 96042003500, Product no 42 SchematicElectrical KEY Part Description 162 DriveRepair Parts Chassis 194263 Drawbar Wheels and Tires Steering Optional Equipment EngineEngine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPolicy

411229 specifications

The Poulan 411229 is a robust and versatile chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its efficiency and reliability, this chainsaw stands out in a crowded market thanks to its advanced features and user-friendly design.

One of the main highlights of the Poulan 411229 is its powerful engine. Equipped with a high-performance gas engine, this chainsaw delivers impressive power that allows for efficient cutting through various types of wood, whether you are tackling thick tree trunks or lighter branches. The engine is designed to minimize exhaust emissions, aligning with modern environmental standards, making it a responsible choice for users who are conscious about their ecological footprint.

The Poulan 411229 features a high-quality bar and chain system. The saw comes with a durable bar that provides excellent cutting capacity while maintaining stability. The chain is engineered for optimal performance, ensuring smooth cutting and longer-lasting sharpness, meaning less time spent on maintenance and more time getting the job done.

An essential aspect of the design is the user comfort it offers. The chainsaw is equipped with an anti-vibration system that significantly reduces operator fatigue during prolonged use. This feature is particularly beneficial for professional arborists and landscapers who depend on their tools for extended periods.

Safety is another priority in the design of the Poulan 411229. The chainsaw includes reliable safety features such as a chain brake that stops the chain in the event of kickback, and a safety throttle that prevents accidental starting. These features are designed to give users peace of mind while operating the tool.

Furthermore, the Poulan 411229 has an easy-start mechanism that simplifies the ignition process. This is particularly advantageous for less experienced users who may struggle with traditional starting methods. The chainsaw also has a tool-less chain tensioning system, allowing for quick adjustments to the chain without the need for additional tools, fostering both convenience and efficiency in operation.

In summary, the Poulan 411229 is a reliable, efficient, and user-friendly chainsaw. Its powerful engine, durable bar and chain, user comfort features, and safety enhancements make it an excellent choice for anyone looking to tackle cutting tasks with confidence and ease. Whether for professional use or weekend projects, this chainsaw represents a smart investment in quality and performance.
Top Page Image Contents