Poulan 411229 manual Tools Required for Assembly, To Remove Tractor from, Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

INSERT

5/16 HEX BOLT

A socket wrench set will make assembly easier. Standard

wrench sizes are listed.

5/16 LOCK WASHER

(1) 1/2" wrench Utility knife

LARGE FLAT WASHER

 

(2)3/4" wrench Tire pressure gauge Pliers

When right or left hand is mentioned in this manual, it means

 

 

when you are in the operating position (seated behind the

 

 

steering wheel).

 

STEERING

 

 

WHEEL

TO REMOVE TRACTOR FROM

STEERING BOOT

 

CARTON

ADAPTER

 

UNPACK CARTON

 

 

• Remove all accessible loose parts and parts cartons

TABS

 

from carton.

TAB

 

• Cut along dashed lines on all four panels of carton.

 

SLOTS

Remove end panels and lay side panels flat.

 

 

• Check for any additional loose parts or cartons and

EXTENSION SHAFT

 

remove.

 

 

 

LOWER STEERING SHAFT

 

BEFORE REMOVING TRACTOR FROM

 

 

SKID

 

03125

ATTACH STEERING WHEEL (See Fig. 1)

FIG. 1

 

ASSEMBLE EXTENSION SHAFT AND BOOT

 

 

• Slide extension shaft onto lower steering shaft.

INSTALL SEAT (See Figs. 2 and 3)

 

• Place tabs of steering boot over tab slots in dash and

 

push down to secure.

• Remove bolt and flat washer securing seat to cardboard

 

packing and set aside for assembly of seat to tractor.

INSTALL STEERING WHEEL

Remove the cardboard packing and discard.

• Position front wheels of the tractor so they are pointing

• Connect switch to seat.

straight forward.

• Place seat on seat pan so all three (3) bottom pads

• Remove steering wheel adapter from steering wheel

are positioned over large slotted holes in pan.

and slide adapter onto steering shaft extension.

 

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB19546LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from AssemblyTools Required for Assembly CartonCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System Reverse Operation System ROSTo Operate Mower See Fig Before Starting the Engine Mowing Tips Maintenance General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Precision SIDE-TO-SIDE Adjustment To Level MowerTo Replace Motion Belt Drive See Fig Belt InstallationTo Replace Mower Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Schematic Tractor - Model Number PB19546LT 96042003500, Product no 42Electrical KEY Part Description Drive 162Repair Parts Chassis 194263 Drawbar Wheels and Tires Steering Engine Optional EquipmentEngine Power Rating Information Mower Deck Repair Parts Seat Mower Lift Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXPolicy

411229 specifications

The Poulan 411229 is a robust and versatile chainsaw designed to meet the needs of both professional users and DIY enthusiasts alike. Known for its efficiency and reliability, this chainsaw stands out in a crowded market thanks to its advanced features and user-friendly design.

One of the main highlights of the Poulan 411229 is its powerful engine. Equipped with a high-performance gas engine, this chainsaw delivers impressive power that allows for efficient cutting through various types of wood, whether you are tackling thick tree trunks or lighter branches. The engine is designed to minimize exhaust emissions, aligning with modern environmental standards, making it a responsible choice for users who are conscious about their ecological footprint.

The Poulan 411229 features a high-quality bar and chain system. The saw comes with a durable bar that provides excellent cutting capacity while maintaining stability. The chain is engineered for optimal performance, ensuring smooth cutting and longer-lasting sharpness, meaning less time spent on maintenance and more time getting the job done.

An essential aspect of the design is the user comfort it offers. The chainsaw is equipped with an anti-vibration system that significantly reduces operator fatigue during prolonged use. This feature is particularly beneficial for professional arborists and landscapers who depend on their tools for extended periods.

Safety is another priority in the design of the Poulan 411229. The chainsaw includes reliable safety features such as a chain brake that stops the chain in the event of kickback, and a safety throttle that prevents accidental starting. These features are designed to give users peace of mind while operating the tool.

Furthermore, the Poulan 411229 has an easy-start mechanism that simplifies the ignition process. This is particularly advantageous for less experienced users who may struggle with traditional starting methods. The chainsaw also has a tool-less chain tensioning system, allowing for quick adjustments to the chain without the need for additional tools, fostering both convenience and efficiency in operation.

In summary, the Poulan 411229 is a reliable, efficient, and user-friendly chainsaw. Its powerful engine, durable bar and chain, user comfort features, and safety enhancements make it an excellent choice for anyone looking to tackle cutting tasks with confidence and ease. Whether for professional use or weekend projects, this chainsaw represents a smart investment in quality and performance.
Top Page Image Contents