Poulan 411256, 96042003700 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

T

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PB20H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See -21 Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Fig la Voir Batterie LA ReplacerAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG20 .FIG 21 .FIG 19 .FIG18 .FIG Tondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantUtilisation 12 .FIGQuetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE Réchauffement11 et 3 .Fig les Voir MAR EN Fonctionnement DE Système10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Desmancom des tionfonc la et MontageLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003700, 411256 specifications

The Poulan 411256, also identified by its part number 96042003700, is a standout product in the world of outdoor power equipment, particularly known for its robust features that cater to both casual users and professional landscapers. This powerful tool is designed to deliver exceptional performance in lawn care, making it an ideal choice for anyone looking to maintain their outdoor spaces efficiently.

One of the key features of the Poulan 411256 is its lightweight design, which enhances user comfort during extended use. Weighing significantly less than many comparable tools, it enables operators to handle it with ease, reducing fatigue and promoting productivity. Ergonomically designed, the unit allows for a comfortable grip, ensuring stability and control while in operation.

In terms of technology, the Poulan 411256 incorporates a powerful engine that provides ample power for various applications. With a displacement capacity that aligns with industry standards, it ensures that users can tackle tough tasks, from trimming and edging to more demanding cutting applications. The engine's efficiency is complemented by its fuel economy, enabling longer periods of uninterrupted operation, which is particularly advantageous for larger properties.

The cutting functionality of the Poulan 411256 is enhanced by its advanced blade technology. The balanced design of the blades not only ensures precision cutting but also contributes to smoother operation. This means that users can achieve cleaner cuts with less effort, leading to healthier plants and a more aesthetically pleasing yard.

Safety is a critical concern with any outdoor power equipment, and the Poulan 411256 addresses this with several built-in safety features. These include a dual-trigger system that prevents accidental starts, as well as protective guards that ensure the operator remains safe from debris and during operation.

Maintenance is made easier with the Poulan 411256, boasting a tool-free assembly for blade changes and quick adjustments, allowing users to spend more time working and less time on upkeep. The durable construction of the unit is also designed to withstand the rigors of frequent use, ensuring longevity and reliability.

In conclusion, the Poulan 411256, 96042003700 combines innovation, user-friendly design, and robust performance. Its lightweight construction, powerful engine, advanced cutting technologies, safety features, and easy maintenance make it an excellent choice for anyone serious about lawn care. Whether for residential or commercial use, this versatile tool is built to meet the demands of modern landscaping.
Top Page Image Contents