Poulan 96042003700, 411256 manual To Replace Mower Drive Belt See Fig, To Check Brake

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT (See Fig. 26)

MOWER DRIVE BELT REMOVAL

Park tractor on a level surface. Engage parking brake.

Lower attachment lift lever to its lowest position.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Remove belt from electric clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Raise attachment lift lever to highest position.

S

M

R

R

FIG. 26

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 27)

Park the tractor on level surface. Engage parking brake.

 

For assistance, there is a belt installation guide decal on

 

bottom side of left footrest.

21

 

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

4.Remove belt downward from engine pulley (E).

5.Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See “TO INSTALL MOWER” in this section of manual).

E

F

A

B G

C

D

FIG. 27

Image 21
Contents Model PB20H46YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Stopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerReverse Operation System ROS Before Starting the EngineTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See -21To Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Replacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie UNE Pliez EST Ceci Degrés Suivant LESConnexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage GAZ DES Commande LA DE Câble LE Régler Pour Starter DU Commande LA Régler PourReglages ET Revision MoteurFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Réglages ET RévisionFreins LES Vérifier Pour 27 .FIG25 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerTondeuse LA Enlever Pour 17 .FIGFig la Voir Entretien’ALLUMAGE Bougie Moteur DE D’HUILE Filtre’AIR Tamis LE Nettoyer AIR À FiltreSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE Tableau12 .FIG UtilisationMoteur LE Démarrer Pour Transmission LA PurgerQuetimaauto Sion Transmis DE RéchauffementMAR EN Fonctionnement DE Système 11 et 3 .Fig les VoirJauge DE Roues LES Régler Pour Tondeuse LA Utiliser Pour10 .FIG Système DU CaractéristiquesVitess GAZ DES Commande LA Utiliser PourDE Régulateur LE Utiliser Comment Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Toncar DU Tracteur LE Sortir Pour Montées NON PiécesFig la Voir Batterie LA Vérifier Fig la Voir Siège LE AjustezSommaire Tracteurs des sécurité toute Général EntretienEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003700, 411256 specifications

The Poulan 411256, also identified by its part number 96042003700, is a standout product in the world of outdoor power equipment, particularly known for its robust features that cater to both casual users and professional landscapers. This powerful tool is designed to deliver exceptional performance in lawn care, making it an ideal choice for anyone looking to maintain their outdoor spaces efficiently.

One of the key features of the Poulan 411256 is its lightweight design, which enhances user comfort during extended use. Weighing significantly less than many comparable tools, it enables operators to handle it with ease, reducing fatigue and promoting productivity. Ergonomically designed, the unit allows for a comfortable grip, ensuring stability and control while in operation.

In terms of technology, the Poulan 411256 incorporates a powerful engine that provides ample power for various applications. With a displacement capacity that aligns with industry standards, it ensures that users can tackle tough tasks, from trimming and edging to more demanding cutting applications. The engine's efficiency is complemented by its fuel economy, enabling longer periods of uninterrupted operation, which is particularly advantageous for larger properties.

The cutting functionality of the Poulan 411256 is enhanced by its advanced blade technology. The balanced design of the blades not only ensures precision cutting but also contributes to smoother operation. This means that users can achieve cleaner cuts with less effort, leading to healthier plants and a more aesthetically pleasing yard.

Safety is a critical concern with any outdoor power equipment, and the Poulan 411256 addresses this with several built-in safety features. These include a dual-trigger system that prevents accidental starts, as well as protective guards that ensure the operator remains safe from debris and during operation.

Maintenance is made easier with the Poulan 411256, boasting a tool-free assembly for blade changes and quick adjustments, allowing users to spend more time working and less time on upkeep. The durable construction of the unit is also designed to withstand the rigors of frequent use, ensuring longevity and reliability.

In conclusion, the Poulan 411256, 96042003700 combines innovation, user-friendly design, and robust performance. Its lightweight construction, powerful engine, advanced cutting technologies, safety features, and easy maintenance make it an excellent choice for anyone serious about lawn care. Whether for residential or commercial use, this versatile tool is built to meet the demands of modern landscaping.