Poulan 411256 Check Tire Pressure, Check Deck Levelness, Check for Proper Position of ALL Belts

Page 6

ASSEMBLY

4.Roll tractor forward off skid.

5.Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

1.Be sure all the above assembly steps have been com- pleted.

2.Check engine oil level and fill fuel tank with gasoline.

3.Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

4.Sit on seat in operating position, depress brake pedal and set the parking brake.

5.Raise attachment lift lever to its highest position.

6.Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this man- ual). After engine has started, move throttle control to idle (slow) position.

7.Release parking brake.

8.Slowly depress forward drive pedal and drive tractor off skid.

9.Apply brake to stop tractor and set parking brake.

10.Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged.

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in “transmission engaged” position (see “TO TRANS- PORT” in the Operation section of this manual).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

✓It is important to purge the transmission before oper- ating your tractor for the first time. Follow proper start- ing and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB20H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsService and Adjustments To Install Mower See -21To Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Tondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantUtilisation 12 .FIGQuetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE Réchauffement11 et 3 .Fig les Voir MAR EN Fonctionnement DE Système10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003700, 411256 specifications

The Poulan 411256, also identified by its part number 96042003700, is a standout product in the world of outdoor power equipment, particularly known for its robust features that cater to both casual users and professional landscapers. This powerful tool is designed to deliver exceptional performance in lawn care, making it an ideal choice for anyone looking to maintain their outdoor spaces efficiently.

One of the key features of the Poulan 411256 is its lightweight design, which enhances user comfort during extended use. Weighing significantly less than many comparable tools, it enables operators to handle it with ease, reducing fatigue and promoting productivity. Ergonomically designed, the unit allows for a comfortable grip, ensuring stability and control while in operation.

In terms of technology, the Poulan 411256 incorporates a powerful engine that provides ample power for various applications. With a displacement capacity that aligns with industry standards, it ensures that users can tackle tough tasks, from trimming and edging to more demanding cutting applications. The engine's efficiency is complemented by its fuel economy, enabling longer periods of uninterrupted operation, which is particularly advantageous for larger properties.

The cutting functionality of the Poulan 411256 is enhanced by its advanced blade technology. The balanced design of the blades not only ensures precision cutting but also contributes to smoother operation. This means that users can achieve cleaner cuts with less effort, leading to healthier plants and a more aesthetically pleasing yard.

Safety is a critical concern with any outdoor power equipment, and the Poulan 411256 addresses this with several built-in safety features. These include a dual-trigger system that prevents accidental starts, as well as protective guards that ensure the operator remains safe from debris and during operation.

Maintenance is made easier with the Poulan 411256, boasting a tool-free assembly for blade changes and quick adjustments, allowing users to spend more time working and less time on upkeep. The durable construction of the unit is also designed to withstand the rigors of frequent use, ensuring longevity and reliability.

In conclusion, the Poulan 411256, 96042003700 combines innovation, user-friendly design, and robust performance. Its lightweight construction, powerful engine, advanced cutting technologies, safety features, and easy maintenance make it an excellent choice for anyone serious about lawn care. Whether for residential or commercial use, this versatile tool is built to meet the demands of modern landscaping.
Top Page Image Contents