Poulan 96042003700, 411256 manual HOW to USE Your Tractor, Stopping

Page 9

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE(See Fig. 4)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

Depress brake pedal (B) all the way down and hold.

Pull parking brake lever (C) up and hold, release pres- sure from brake pedal (B), then release parking brake lever. Pedal should remain in brake position. Make sure parking brake will hold tractor secure.

B

C

FIG. 4

STOPPING

MOWER BLADES -

To stop mower blades, move attachment clutch lever to disengaged position ( ).

FIG. 5

(

) Attachment

(

) Disengaged

 

Clutch

 

Position

 

Engage Position

 

 

GROUND DRIVE -

To stop ground drive, depress brake pedal all the way down.

ENGINE -

Move throttle control (D) between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause en- gine to “backfire”.

Turn ignition key (F) to “STOP” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will cause the battery to discharge and go dead.

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely, as described above, before leaving the operator's position.

D

F

N

FIG. 6

TO USE THROTTLE CONTROL - D (See Fig. 6)

Always operate engine at full speed (fast).

Operating engine at less than full speed (fast) reduces engines operating efficiency.

Full speed (fast) offers the best bagging and mower performance.

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

Start tractor and release parking brake.

Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL -J (See Fig. 7)

The cruise control feature can be used for forward travel only.

9

Image 9
Contents Model PB20H46YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Stopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerReverse Operation System ROS Before Starting the EngineTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See -21To Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Replacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie UNE Pliez EST Ceci Degrés Suivant LESConnexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage GAZ DES Commande LA DE Câble LE Régler Pour Starter DU Commande LA Régler PourReglages ET Revision MoteurFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Réglages ET RévisionFreins LES Vérifier Pour 27 .FIG25 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Fig Voir Courroie LA ET Tondeuse LA InstallerTondeuse LA Enlever Pour 17 .FIGFig la Voir Entretien’ALLUMAGE Bougie Moteur DE D’HUILE Filtre’AIR Tamis LE Nettoyer AIR À FiltreSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE Tableau12 .FIG UtilisationMoteur LE Démarrer Pour Transmission LA PurgerQuetimaauto Sion Transmis DE RéchauffementMAR EN Fonctionnement DE Système 11 et 3 .Fig les VoirJauge DE Roues LES Régler Pour Tondeuse LA Utiliser Pour10 .FIG Système DU CaractéristiquesVitess GAZ DES Commande LA Utiliser PourDE Régulateur LE Utiliser Comment Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Toncar DU Tracteur LE Sortir Pour Montées NON PiécesFig la Voir Batterie LA Vérifier Fig la Voir Siège LE AjustezSommaire Tracteurs des sécurité toute Général EntretienEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003700, 411256 specifications

The Poulan 411256, also identified by its part number 96042003700, is a standout product in the world of outdoor power equipment, particularly known for its robust features that cater to both casual users and professional landscapers. This powerful tool is designed to deliver exceptional performance in lawn care, making it an ideal choice for anyone looking to maintain their outdoor spaces efficiently.

One of the key features of the Poulan 411256 is its lightweight design, which enhances user comfort during extended use. Weighing significantly less than many comparable tools, it enables operators to handle it with ease, reducing fatigue and promoting productivity. Ergonomically designed, the unit allows for a comfortable grip, ensuring stability and control while in operation.

In terms of technology, the Poulan 411256 incorporates a powerful engine that provides ample power for various applications. With a displacement capacity that aligns with industry standards, it ensures that users can tackle tough tasks, from trimming and edging to more demanding cutting applications. The engine's efficiency is complemented by its fuel economy, enabling longer periods of uninterrupted operation, which is particularly advantageous for larger properties.

The cutting functionality of the Poulan 411256 is enhanced by its advanced blade technology. The balanced design of the blades not only ensures precision cutting but also contributes to smoother operation. This means that users can achieve cleaner cuts with less effort, leading to healthier plants and a more aesthetically pleasing yard.

Safety is a critical concern with any outdoor power equipment, and the Poulan 411256 addresses this with several built-in safety features. These include a dual-trigger system that prevents accidental starts, as well as protective guards that ensure the operator remains safe from debris and during operation.

Maintenance is made easier with the Poulan 411256, boasting a tool-free assembly for blade changes and quick adjustments, allowing users to spend more time working and less time on upkeep. The durable construction of the unit is also designed to withstand the rigors of frequent use, ensuring longevity and reliability.

In conclusion, the Poulan 411256, 96042003700 combines innovation, user-friendly design, and robust performance. Its lightweight construction, powerful engine, advanced cutting technologies, safety features, and easy maintenance make it an excellent choice for anyone serious about lawn care. Whether for residential or commercial use, this versatile tool is built to meet the demands of modern landscaping.