Poulan 411256 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See -21

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 17)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Roll belt off engine pulley (M) and belt keepers (G).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE

MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig.17-21)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

•ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D)

G M F

Q RG

P

A E

B

C

K

D

 

L

FIG. 17

 

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PB20H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsService and Adjustments To Install Mower See -21To Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Tondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantUtilisation 12 .FIGQuetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE Réchauffement11 et 3 .Fig les Voir MAR EN Fonctionnement DE Système10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042003700, 411256 specifications

The Poulan 411256, also identified by its part number 96042003700, is a standout product in the world of outdoor power equipment, particularly known for its robust features that cater to both casual users and professional landscapers. This powerful tool is designed to deliver exceptional performance in lawn care, making it an ideal choice for anyone looking to maintain their outdoor spaces efficiently.

One of the key features of the Poulan 411256 is its lightweight design, which enhances user comfort during extended use. Weighing significantly less than many comparable tools, it enables operators to handle it with ease, reducing fatigue and promoting productivity. Ergonomically designed, the unit allows for a comfortable grip, ensuring stability and control while in operation.

In terms of technology, the Poulan 411256 incorporates a powerful engine that provides ample power for various applications. With a displacement capacity that aligns with industry standards, it ensures that users can tackle tough tasks, from trimming and edging to more demanding cutting applications. The engine's efficiency is complemented by its fuel economy, enabling longer periods of uninterrupted operation, which is particularly advantageous for larger properties.

The cutting functionality of the Poulan 411256 is enhanced by its advanced blade technology. The balanced design of the blades not only ensures precision cutting but also contributes to smoother operation. This means that users can achieve cleaner cuts with less effort, leading to healthier plants and a more aesthetically pleasing yard.

Safety is a critical concern with any outdoor power equipment, and the Poulan 411256 addresses this with several built-in safety features. These include a dual-trigger system that prevents accidental starts, as well as protective guards that ensure the operator remains safe from debris and during operation.

Maintenance is made easier with the Poulan 411256, boasting a tool-free assembly for blade changes and quick adjustments, allowing users to spend more time working and less time on upkeep. The durable construction of the unit is also designed to withstand the rigors of frequent use, ensuring longevity and reliability.

In conclusion, the Poulan 411256, 96042003700 combines innovation, user-friendly design, and robust performance. Its lightweight construction, powerful engine, advanced cutting technologies, safety features, and easy maintenance make it an excellent choice for anyone serious about lawn care. Whether for residential or commercial use, this versatile tool is built to meet the demands of modern landscaping.
Top Page Image Contents