Poulan 411259 manual To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

T

FIG. 8

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PB22H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Ignition Switch Used for starting and stopping the engine Know Your TractorHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterBefore Starting the Engine To Operate on HillsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty L5V 3E4Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciRemarque Garantie cette de exclus sont normal l’entretien et AutoriséInitiale d’achat date la de compter à jours 90 dix Dépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Carburateur LE Régler Pour GAZ DES CommandeReglages ET Revision Fig la Voir Batterie LA ReplacerFig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE 29 .FIGFrein LE Régler ET Contrôler Pour Réglages ET RévisionFig la Voir ’EN Courroie LA Remplacer Pour24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG18 .FIG 21 .FIG 19 .FIG20 .FIG Place en bien est courroie la que vous-Assurez ImportantFig Voir Courroie LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Tondeuse LA Enlever Pour’ALLUMAGE Bougie Ligne EN Installe Dessence FiltreEntretien Moteur DE D’HUILE FiltreMoteur Fig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantTransmission LA Purger Avant ET Réinstallation LA Après Purgée ÊtreUtilisation 12 .FIGMoteur DU D’HUILE Niveau LE Vérifier R R a M É D’ESSENCE Réservoir LE Remplir Quetimaauto11 et 3 .Fig les Voir Accessoires Autres ET Charrettes DES Remorquer Pour’ENTRETIEN/HOROMÈTRE Indicateur Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour VitessDE Régulateur LE Utiliser Comment Jauge DE Roues LES Régler PourFig la Voir Mentnetionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourLétrangleur Utiliser Pour Fig la Voir Arrêter Pour 4 .FIGFroid moteur un démarrer de permet Détrangleur Commande N Moteur de vitesse la commander de permet GAZ DES Commande D’EMBRAYAGE Tionsec la Voir Conduisant LE EN Telet MontageDesmancom des tionfonc la et PA LA DE Tracteur LE Retirer PourMontées NON Piéces Toncar DU Tracteur LE Sortir PourSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils Pelouse DE Tracteur PB22H46YT Modèle Lopérateur DE Manuel

411259 specifications

The Poulan 411259 is a powerful and efficient chainsaw that caters to both casual users and professionals alike. Known for its reliability and performance, this model integrates advanced features and technology to ensure it meets the demands of various cutting tasks, whether it's for trimming branches, cutting firewood, or clearing fallen trees.

One of the standout features of the Poulan 411259 is its robust 42cc engine, which provides ample power for demanding jobs without compromising on ease of use. The engine is designed to deliver strong performance while maintaining fuel efficiency, making it an environmentally friendly choice for users who want to minimize their carbon footprint. Additionally, the chainsaw is equipped with a 16-inch bar and chain, allowing for a sufficient cutting capacity that is ideal for handling mid-sized logs and branches with ease.

Another key technology incorporated in the Poulan 411259 is its automatic oiling system. This feature ensures that the chain is consistently lubricated during operation, reducing friction and heat buildup, which ultimately prolongs the life of the chain and bar. This self-lubricating system contributes to smoother cuts and enhances the overall performance of the chainsaw.

User comfort is also a priority in the design of the Poulan 411259. The chainsaw is built with an ergonomic handle that allows for a secure grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances maneuverability, making it easier to navigate through branches and tight spaces. The accessible controls provide straightforward operation, ensuring that both seasoned users and novices can handle the tool effectively.

Safety features are paramount in the Poulan 411259, which includes a chain brake that halts the chain's movement in the event of kickback. The protective design elements help to ensure that users can operate the chainsaw with confidence, knowing that safety measures are in place.

In summary, the Poulan 411259 combines power, efficiency, and user-friendly features in a reliable chainsaw. With its durable engine, automatic lubrication, ergonomic design, and essential safety technologies, it stands out as an excellent tool for tackling a variety of cutting jobs in both residential and professional settings. Whether one is maintaining a garden or managing larger woodcutting tasks, the Poulan 411259 is a capable companion that delivers consistent results.
Top Page Image Contents