Poulan 411259 manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

 

 

MANDREL

 

 

 

ASSEMBLY

 

CENTER

 

 

 

HOLE

 

 

BLADE BOLT

 

 

 

(SPECIAL)

0

2

544

 

 

 

 

 

 

 

 

 

STAR

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model PB22H46YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Ignition Switch Used for starting and stopping the engineHOW to USE Your Tractor To Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Reverse Operation System ROSAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Schedule MaintenanceMaintenance General RecommendationsTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Mower Drive BeltTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when L5V 3E4 Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESRemarque Autorisé Garantie cette de exclus sont normal l’entretien etInitiale d’achat date la de compter à jours 90 dix Connexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Fig la Voir Batterie LA Replacer GAZ DES CommandeReglages ET Revision Carburateur LE Régler Pour29 .FIG Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Fig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour’EN Courroie LA Remplacer Pour Réglages ET RévisionFig la Voir Frein LE Régler ET Contrôler Pour23 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 24 .FIGPlace en bien est courroie la que vous-Assurez Important 21 .FIG 19 .FIG20 .FIG 18 .FIGTondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Fig VoirMoteur DE D’HUILE Filtre Ligne EN Installe Dessence FiltreEntretien ’ALLUMAGE BougieMoteur EN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE Tableau12 .FIG Avant ET Réinstallation LA Après Purgée ÊtreUtilisation Transmission LA PurgerQuetimaauto R R a M É D’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierPentes LES Dans Utiliser Pour Accessoires Autres ET Charrettes DES Remorquer Pour’ENTRETIEN/HOROMÈTRE Indicateur 11 et 3 .Fig les VoirJauge DE Roues LES Régler Pour VitessDE Régulateur LE Utiliser Comment Tondeuse LA Utiliser PourFig la Voir Arrêter Pour 4 .FIG GAZ DES Commande LA Utiliser PourLétrangleur Utiliser Pour Fig la Voir Mentnetionsta DE Frein LE Engager PourMoteur de vitesse la commander de permet GAZ DES Commande D Froid moteur un démarrer de permet Détrangleur Commande N’EMBRAYAGE PA LA DE Tracteur LE Retirer Pour MontageDesmancom des tionfonc la et Tionsec la Voir Conduisant LE EN TeletToncar DU Tracteur LE Sortir Pour Montées NON PiécesSommaire ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Pelouse DE Tracteur PB22H46YT Modèle Lopérateur DE Manuel

411259 specifications

The Poulan 411259 is a powerful and efficient chainsaw that caters to both casual users and professionals alike. Known for its reliability and performance, this model integrates advanced features and technology to ensure it meets the demands of various cutting tasks, whether it's for trimming branches, cutting firewood, or clearing fallen trees.

One of the standout features of the Poulan 411259 is its robust 42cc engine, which provides ample power for demanding jobs without compromising on ease of use. The engine is designed to deliver strong performance while maintaining fuel efficiency, making it an environmentally friendly choice for users who want to minimize their carbon footprint. Additionally, the chainsaw is equipped with a 16-inch bar and chain, allowing for a sufficient cutting capacity that is ideal for handling mid-sized logs and branches with ease.

Another key technology incorporated in the Poulan 411259 is its automatic oiling system. This feature ensures that the chain is consistently lubricated during operation, reducing friction and heat buildup, which ultimately prolongs the life of the chain and bar. This self-lubricating system contributes to smoother cuts and enhances the overall performance of the chainsaw.

User comfort is also a priority in the design of the Poulan 411259. The chainsaw is built with an ergonomic handle that allows for a secure grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances maneuverability, making it easier to navigate through branches and tight spaces. The accessible controls provide straightforward operation, ensuring that both seasoned users and novices can handle the tool effectively.

Safety features are paramount in the Poulan 411259, which includes a chain brake that halts the chain's movement in the event of kickback. The protective design elements help to ensure that users can operate the chainsaw with confidence, knowing that safety measures are in place.

In summary, the Poulan 411259 combines power, efficiency, and user-friendly features in a reliable chainsaw. With its durable engine, automatic lubrication, ergonomic design, and essential safety technologies, it stands out as an excellent tool for tackling a variety of cutting jobs in both residential and professional settings. Whether one is maintaining a garden or managing larger woodcutting tasks, the Poulan 411259 is a capable companion that delivers consistent results.
Top Page Image Contents