Poulan 411259 manual To Replace Motion Drive Belt See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 28)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler (A) and clutching idler (B).

•Remove belt from centerspan idler (C).

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

•Remove belt downward from engine pulley (E).

•Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

•Pull belt toward front of tractor and roll belt onto engine pulley (E).

•Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (C).

•Install belt through stationary idler (A) and clutching idler (B).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

E

F

A

B G

C

D

FIG. 28

22

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 29)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 29

TO START ENGINE WITH A WEAK BATTERY (See Fig. 30)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB22H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Ignition Switch Used for starting and stopping the engine Know Your TractorHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerReverse Operation System ROS Service REMINDER/HOUR MeterBefore Starting the Engine To Operate on HillsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty L5V 3E4Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciRemarque Garantie cette de exclus sont normal l’entretien et AutoriséInitiale d’achat date la de compter à jours 90 dix Dépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Carburateur LE Régler Pour GAZ DES CommandeReglages ET Revision Fig la Voir Batterie LA ReplacerFig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE 29 .FIGFrein LE Régler ET Contrôler Pour Réglages ET RévisionFig la Voir ’EN Courroie LA Remplacer Pour24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG18 .FIG 21 .FIG 19 .FIG20 .FIG Place en bien est courroie la que vous-Assurez ImportantFig Voir Courroie LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Tondeuse LA Enlever Pour’ALLUMAGE Bougie Ligne EN Installe Dessence FiltreEntretien Moteur DE D’HUILE FiltreMoteur Fig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantTransmission LA Purger Avant ET Réinstallation LA Après Purgée ÊtreUtilisation 12 .FIGMoteur DU D’HUILE Niveau LE Vérifier R R a M É D’ESSENCE Réservoir LE Remplir Quetimaauto11 et 3 .Fig les Voir Accessoires Autres ET Charrettes DES Remorquer Pour’ENTRETIEN/HOROMÈTRE Indicateur Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour VitessDE Régulateur LE Utiliser Comment Jauge DE Roues LES Régler PourFig la Voir Mentnetionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourLétrangleur Utiliser Pour Fig la Voir Arrêter Pour 4 .FIGFroid moteur un démarrer de permet Détrangleur Commande N Moteur de vitesse la commander de permet GAZ DES Commande D’EMBRAYAGE Tionsec la Voir Conduisant LE EN Telet MontageDesmancom des tionfonc la et PA LA DE Tracteur LE Retirer PourMontées NON Piéces Toncar DU Tracteur LE Sortir PourSommaire En l’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils Pelouse DE Tracteur PB22H46YT Modèle Lopérateur DE Manuel

411259 specifications

The Poulan 411259 is a powerful and efficient chainsaw that caters to both casual users and professionals alike. Known for its reliability and performance, this model integrates advanced features and technology to ensure it meets the demands of various cutting tasks, whether it's for trimming branches, cutting firewood, or clearing fallen trees.

One of the standout features of the Poulan 411259 is its robust 42cc engine, which provides ample power for demanding jobs without compromising on ease of use. The engine is designed to deliver strong performance while maintaining fuel efficiency, making it an environmentally friendly choice for users who want to minimize their carbon footprint. Additionally, the chainsaw is equipped with a 16-inch bar and chain, allowing for a sufficient cutting capacity that is ideal for handling mid-sized logs and branches with ease.

Another key technology incorporated in the Poulan 411259 is its automatic oiling system. This feature ensures that the chain is consistently lubricated during operation, reducing friction and heat buildup, which ultimately prolongs the life of the chain and bar. This self-lubricating system contributes to smoother cuts and enhances the overall performance of the chainsaw.

User comfort is also a priority in the design of the Poulan 411259. The chainsaw is built with an ergonomic handle that allows for a secure grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances maneuverability, making it easier to navigate through branches and tight spaces. The accessible controls provide straightforward operation, ensuring that both seasoned users and novices can handle the tool effectively.

Safety features are paramount in the Poulan 411259, which includes a chain brake that halts the chain's movement in the event of kickback. The protective design elements help to ensure that users can operate the chainsaw with confidence, knowing that safety measures are in place.

In summary, the Poulan 411259 combines power, efficiency, and user-friendly features in a reliable chainsaw. With its durable engine, automatic lubrication, ergonomic design, and essential safety technologies, it stands out as an excellent tool for tackling a variety of cutting jobs in both residential and professional settings. Whether one is maintaining a garden or managing larger woodcutting tasks, the Poulan 411259 is a capable companion that delivers consistent results.
Top Page Image Contents