Poulan 411259 To Replace Mower Drive Belt, To Check and Adjust Brake See Fig, To Check Brake

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 26) -

•Park tractor on a level surface. Engage parking brake. Disengage attachment clutch control.

•Remove screws from L.H. mandrel cover and remove cover.

•Remove small retainer spring and lift clutch spring off pulley bolt.

•Roll belt over the top of L.H. mandrel pulley.

•Remove belt from engine pulley.

•Remove belt from idler pulleys.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Check primary idler arm and two idlers to see that they rotate freely.

MOWER DRIVE BELT INSTALLATION (See Fig. 26) -

•Install belt in both idlers. Make sure belt is in both belt keepers at the idlers as shown.

•Install new belt onto engine pulley.

•Roll belt into upper groove of L.H. mandrel pulley.

•Carefully check belt routing making sure belt is in the grooves correctly and inside belt keepers.

•Reassemble clutch spring to pulley bolt.

•Reassemble L.H. mandrel cover.

S

M

R

R

FIG. 26

TO CHECK AND ADJUST BRAKE (See Fig. 27)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-3/4"

NUT “A”

JAM NUT

OPERATING

ARM

02537

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE AD- JUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 27

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model PB22H46YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Ignition Switch Used for starting and stopping the engineHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Adjust Brake To Check and Adjust Brake See FigTo Replace Mower Drive Belt To Check BrakeTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when L5V 3E4 Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESRemarque Autorisé Garantie cette de exclus sont normal l’entretien etInitiale d’achat date la de compter à jours 90 dix Connexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Reglages ET Revision GAZ DES CommandeCarburateur LE Régler Pour Fig la Voir Batterie LA ReplacerAvant Roue LA DE PINCEMENT/CARROSSAGE Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourFig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour 29 .FIGFig la Voir Réglages ET RévisionFrein LE Régler ET Contrôler Pour ’EN Courroie LA Remplacer Pour25 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG20 .FIG 21 .FIG 19 .FIG18 .FIG Place en bien est courroie la que vous-Assurez ImportantFigs Voir D’ENTRAÎNEMENT Courroie LA ET Tondeuse LA InstallerFig Voir Tondeuse LA Enlever PourEntretien Ligne EN Installe Dessence Filtre’ALLUMAGE Bougie Moteur DE D’HUILE FiltreMoteur EN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE TableauUtilisation Avant ET Réinstallation LA Après Purgée ÊtreTransmission LA Purger 12 .FIG’ESSENCE Réservoir LE Remplir R R a M É DMoteur DU D’HUILE Niveau LE Vérifier Quetimaauto’ENTRETIEN/HOROMÈTRE Indicateur Accessoires Autres ET Charrettes DES Remorquer Pour11 et 3 .Fig les Voir Pentes LES Dans Utiliser PourDE Régulateur LE Utiliser Comment VitessTondeuse LA Utiliser Pour Jauge DE Roues LES Régler PourLétrangleur Utiliser Pour GAZ DES Commande LA Utiliser PourFig la Voir Mentnetionsta DE Frein LE Engager Pour Fig la Voir Arrêter Pour 4 .FIGMoteur de vitesse la commander de permet GAZ DES Commande D Froid moteur un démarrer de permet Détrangleur Commande N’EMBRAYAGE Desmancom des tionfonc la et MontageTionsec la Voir Conduisant LE EN Telet PA LA DE Tracteur LE Retirer PourToncar DU Tracteur LE Sortir Pour Montées NON PiécesSommaire Tracteurs des sécurité toute Général EntretienEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Pelouse DE Tracteur PB22H46YT Modèle Lopérateur DE Manuel

411259 specifications

The Poulan 411259 is a powerful and efficient chainsaw that caters to both casual users and professionals alike. Known for its reliability and performance, this model integrates advanced features and technology to ensure it meets the demands of various cutting tasks, whether it's for trimming branches, cutting firewood, or clearing fallen trees.

One of the standout features of the Poulan 411259 is its robust 42cc engine, which provides ample power for demanding jobs without compromising on ease of use. The engine is designed to deliver strong performance while maintaining fuel efficiency, making it an environmentally friendly choice for users who want to minimize their carbon footprint. Additionally, the chainsaw is equipped with a 16-inch bar and chain, allowing for a sufficient cutting capacity that is ideal for handling mid-sized logs and branches with ease.

Another key technology incorporated in the Poulan 411259 is its automatic oiling system. This feature ensures that the chain is consistently lubricated during operation, reducing friction and heat buildup, which ultimately prolongs the life of the chain and bar. This self-lubricating system contributes to smoother cuts and enhances the overall performance of the chainsaw.

User comfort is also a priority in the design of the Poulan 411259. The chainsaw is built with an ergonomic handle that allows for a secure grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances maneuverability, making it easier to navigate through branches and tight spaces. The accessible controls provide straightforward operation, ensuring that both seasoned users and novices can handle the tool effectively.

Safety features are paramount in the Poulan 411259, which includes a chain brake that halts the chain's movement in the event of kickback. The protective design elements help to ensure that users can operate the chainsaw with confidence, knowing that safety measures are in place.

In summary, the Poulan 411259 combines power, efficiency, and user-friendly features in a reliable chainsaw. With its durable engine, automatic lubrication, ergonomic design, and essential safety technologies, it stands out as an excellent tool for tackling a variety of cutting jobs in both residential and professional settings. Whether one is maintaining a garden or managing larger woodcutting tasks, the Poulan 411259 is a capable companion that delivers consistent results.
Top Page Image Contents