Poulan PBGTE, 406255 manual To Replace Mower Blade Drive Belt, To Check Brake

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 32)

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and re- move covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

P

Q

LM

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 33)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

• Disconnect clutch wire harness (A).

• Remove anti-rotation link (B) on right side of tractor.

• Remove belt from stationary idler (C) and clutching

idler (D).

• Remove belt from centerspan idler (E).

• Pull belt slack toward rear of tractor. Carefully remove

belt upwards from transmission input pulley and over

cooling fan blades (F).

• Remove belt downward from engine pulley and around

electric clutch (G).

• Slide belt toward rear of tractor, off the steering plate

KR

R

S

P

Q

(H) and remove from tractor.

BELT INSTALLATION -

• Install new belt from tractor rear to front, over the steer-

ing plate (H) and above clutch brake pedal shaft (J).

• Pull belt toward front of tractor and roll belt around

electric clutch and onto engine pulley (G).

• Pull belt toward rear of tractor. Carefully work belt down

around transmission cooling fan and onto the input

pulley (F). Be sure belt is inside the belt keeper.

• Install belt on centerspan idler (E).

R

FIG. 32

• Install belt through stationary idler (C) and clutching

idler (D).

• Reinstall anti-rotation link (B) on right side of tractor.

Tighten securely.

• Reconnect clutch harness (A).

• Make sure belt is in all pulley grooves and inside all

belt guides and keepers.

• Install mower (See “TO INSTALL MOWER” in this sec-

tion of manual).

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation PbgtgeII. Slope Operation Safety RulesSafe Operation Practices for RIDE-ON Mowers General OperationIV. Towing ServiceSafe Operation Practices for RIDE-ON Mowers III. Children Table of Contents Keys Unassembled PartsMower Mower Front Wheel Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Mower See Fig Install Mower and Drive Belt See FigsFirst Install ANTI-SWAY BAR S Assemble Front Wheel to7/16 Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo USE Cruise Control -J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerTo Level Mower Service and AdjustmentsTo Install Mower To Remove Mower See FigTurn nut right Turn nut left To raise mower To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive BeltTo Check Brake To Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when Page Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PBGTE, 406255 specifications

The Poulan 406255, PBGTE is a powerful and versatile tool designed for home and commercial use, particularly favored for its performance in landscaping and yard maintenance tasks. Known for its reliability, this gas-powered string trimmer combines efficiency with user-friendly features, making it an excellent choice for both novices and experienced users alike.

One of the standout features of the Poulan 406255, PBGTE is its robust 25 cc, 2-cycle gas engine. This powerful engine offers a perfect balance of performance and fuel efficiency, allowing users to tackle tough jobs without frequent refueling. The engine’s design also ensures smoother operation, providing consistent power to the cutting head for a cleaner cut and enhanced productivity.

The trimmer’s lightweight design, weighing in under 10 pounds, enhances maneuverability and reduces user fatigue during extended use. The adjustable handle provides an additional layer of comfort, allowing users to customize the grip for optimal control. This feature is particularly beneficial for extensive trimming sessions, where comfort is paramount to achieving professional results.

Equipped with a dual-line cutting head, the Poulan 406255, PBGTE delivers an impressive cutting width that allows users to cover more ground with fewer passes. The trimmer is designed for easy line replacement, which minimizes downtime. Users can quickly reload the cutting line, ensuring that they can get back to work without delays.

Another notable technology integrated into the Poulan 406255, PBGTE is the Easy Start system. This system simplifies the starting process, making it easier for users to start the engine with minimal effort. As a result, even those unfamiliar with gas-powered tools will appreciate the straightforward functionality of this trimmer.

For maximum safety, the tool includes features such as a protective debris shield, which helps protect the user from flying debris while trimming. The combination of safety aspects and robust performance makes the Poulan 406255, PBGTE a dependable choice for varied landscaping tasks.

In conclusion, the Poulan 406255, PBGTE stands out for its powerful engine, ergonomic design, dual-line cutting head, Easy Start technology, and safety features. This trimmer offers a blend of efficiency, comfort, and safety, making it an essential tool for anyone looking to maintain their outdoor space effectively. Whether you are trimming grass, weeds, or smaller brushes, this trimmer is built to handle the challenge with ease and reliability.
Top Page Image Contents