Poulan 96018000500, 532 43 88-96 manual To Level Mower Housing, SIDE-TO-SIDE Adjustment See Figs

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See the sides of tire for proper P.S.I.). If tires are over or underin- flated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

Fig. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

Fig. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

Fig. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

Fig. 19

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents PO15538LT II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other Attachments Reverse Operation System ROSTo Operate on Hills To TransportTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations MaintenanceBlade Removal See Fig BatteryTractor Blade CareEngine Engine Cooling System See Fig CleaningIN-LINE Fuel Filter See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig SIDE-TO-SIDE Adjustment See Figs To Level Mower HousingTo Check Brake To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Excessive Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty

532 43 88-96, 96018000500 specifications

The Poulan 96018000500,532 43 88-96 is a versatile and powerful tool designed for various outdoor tasks, particularly for homeowners and landscaping professionals. This particular model stands out due to its robust performance and user-friendly features.

One of the notable characteristics of the Poulan 96018000500 is its powerful engine, which is engineered to deliver reliable performance for a range of applications. This engine not only provides sufficient power to handle tough cutting jobs but also ensures fuel efficiency, allowing users to complete their tasks without frequent refueling interruptions.

In addition to its engine, the Poulan 96018000500 incorporates advanced technology that enhances its usability. The tool features an intuitive starting mechanism that simplifies the ignition process, making it easier for users to start the machine with minimal effort. This is particularly beneficial for those who may not have extensive experience with outdoor equipment.

The design of the Poulan 96018000500 is also noteworthy. It features an ergonomic handle that provides a comfortable grip and reduces user fatigue during extended use. This is an important consideration for landscaping work, where operators may be required to use the tool for long periods. The lightweight construction of the equipment contributes to its maneuverability, allowing users to work efficiently in various terrains.

Durability is another key characteristic of the Poulan 96018000500. Constructed with high-quality materials, this tool is built to withstand harsh outdoor conditions and resist wear and tear. This reliability ensures that users can depend on their equipment for years without compromising performance.

Moreover, the Poulan 96018000500 is designed for versatility. It is compatible with a range of attachments, allowing users to convert it for different tasks such as trimming, edging, and blowing debris. This adaptability makes it an essential addition to any homeowner's toolkit or professional landscaper's arsenal.

In summary, the Poulan 96018000500,532 43 88-96 combines power, efficiency, and user-centric design, making it a standout choice for outdoor maintenance. With its advanced starting technology, ergonomic features, and durability, this tool meets the demands of both casual users and professionals alike. Whether tackling simple yard maintenance or more demanding landscaping tasks, the Poulan 96018000500 proves to be a reliable partner in enhancing outdoor spaces.
Top Page Image Contents