Poulan 96042010800, 430092 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

K

J

L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PB22H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor CJKStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Turn nut right Turn nut left To raise mower To lower mowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Service and AdjustmentsTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Fires when turn To run when operBattery will not Engine continuesOnly Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products Outdoor Canada AuGarantie cette de exclus sont normal l’entretien et Degrés MAX Dépannage DE Guide Moteur le quand ieuxPuissance de Entreposage Moteur Reglages ET RevisionSionmistrans 34 .Fig Avant Roue LA DE PINCEMENT/CARROSSAGE33 .Fig Freins LES Vérifier Pour Fig LA Voir D’ENTRAÎNEMENT Courroie LA Remplacer PourFig La Voir Tondeuse DE Lame DE Courroie LA Remplacer Pour 32 .Fig29 .Fig Tondeuse LA Niveau LE Ajuster Pour30 .Fig 28 .Fig23 .Fig 26 .Fig25 .Fig 22 .Fig21 .Fig Fig VoirTondeuse LA Enlever Pour GagedFig La Voir Coupe DE Plateau DU Lavage DE Raccord Ligne EN Installe Dessence FiltreEntretien Fig la Voir’AIR Tamis LE Nettoyer ’ALLUMAGE BougieVentilation DE Système Moteur DE L’HUILE Changer PourPneus Fig la Voir Lame LA EnleverLames DES Entretien Frein DU FonctionnementUtilisation Chaque Avant Ce de Réglages et Etretien section la dans réglages les TousTransmission LA Purger Avant ET Réinstallation LA Après Purgée ÊtreUtilisation 13 .FigMoteur DU D’HUILE Niveau LE Vérifier Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir QuetiTracteur LE Transporter Pour Accessoires Autres ET Charrettes DES Remorquer PourTondeuse DE Lames LES Arrêter Pour Pentes LES Dans Utiliser PourTondeuse LA Utiliser Pour Fig la Voir J- Vitess DE Régulateur LE Utiliser CommentFig la Jauge DE Roues LES Régler PourFig la Voir Mentnetionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourFig la Voir D Tondeuse DE LamesUtilisation Frein DE Pédale Desmancom des fonction la et MontageTionsec la Voir Rouler Faisant LE EN TE Fig la Voir Batterie LA Vérifier Assemblé PAS PiècesFig la Voir Siège LE Ajustez Clés pente-GuideCCA .MIN AMP/HR U1R DimensionSommaire SL-SG-APITracteurs des sécurité toute en l’utilisation pour Conseils Sécurité DE RèglesEnfants Entretien’éboule bord le si précipiter de ou bord Pentes LES Dans FonctionnementGénéral Fonctionnement Veuillezlire,comprendreetsuivrelesinstructionsquevoustrouREV Avertissement

96042010800, 430092 specifications

The Poulan 430092, also known by its part number 96042010800, is a high-performance chainsaw that caters to both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Known for its durability, versatility, and user-friendly design, it stands out as a go-to choice in the realm of outdoor equipment.

One of the most notable features of the Poulan 430092 is its powerful engine. Equipped with a robust 40cc two-stroke engine, this chainsaw delivers ample power for cutting through tough wood and handling larger tasks with ease. The engine’s design promotes efficient fuel consumption, allowing for longer use between refueling sessions. This is particularly beneficial for users who need to complete extensive projects without frequent interruptions.

Another characteristic that sets the Poulan 430092 apart is its lightweight design. Weighing under 12 pounds, the chainsaw is easy to maneuver, making it ideal for both aerial pruning and ground-level cutting. Its ergonomic handle provides comfort during extended use, helping to reduce fatigue. Additionally, the chainsaw features an anti-vibration system that absorbs shock, further enhancing user comfort.

The chainsaw is equipped with a 16-inch guide bar and chain, allowing for a greater cutting capacity and making it well-suited for tackling medium to large-sized trees and logs. Its low kickback chain enhances safety, providing peace of mind when operating the saw.

The Poulan 430092 also incorporates advanced technologies such as an automatic oiling system, which ensures that the chain remains well-lubricated during operation. This system prevents excessive wear and tear and prolongs the life of the chainsaw. The easy-access air filter is another innovative feature, allowing users to quickly clean or replace the filter, which helps to maintain optimal engine performance.

In terms of safety, the chainsaw comes with a safety switch that prevents accidental starting, and the chain brake offers additional protection by stopping the chain in case of kickback. These features make the Poulan 430092 not only efficient but also safe for users of all experience levels.

Overall, the Poulan 430092,96042010800 is a reliable and powerful chainsaw that provides excellent performance, user-friendly features, and advanced technologies, making it an excellent investment for anyone needing a dependable cutting tool. Its combination of power, safety, and efficiency continues to earn it a solid reputation in the market for outdoor power equipment.
Top Page Image Contents