Poulan 430092 manual To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

IDLER

PULLEYS

MANDREL

PULLEY

MANDREL

PULLEY

Fig. 31

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 32)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Remove belt from stationary idler (A) and clutching idler (B).

3.Remove belt from centerspan idler (C).

4.Pull belt slack toward rear of tractor. Remove belt upwards from transaxle input pulley (D).

5.Remove belt downward from engine pulley (E).

6.Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

2.Pull belt toward front of tractor and roll belt onto engine pulley (E).

3.Pull belt toward rear of tractor. Carefully work belt down around transaxle input pulley (D). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (C).

5.Install belt through stationary idler (A) and clutching idler (B).

6.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

7.Install mower (See “TO INSTALL MOWER” section in

this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

Fig. 32

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model PB22H46YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation CJK Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig To Stop Mower BladesTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Turn nut right Turn nut left To raise mower To lower mower To Level MowerTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Service and AdjustmentsFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTransmission Other StorageFuel System Engine OILTroubleshooting Battery will not To run when operFires when turn Engine continuesFold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXHOP Outdoor Products Customer Service DeptCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USADept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Degrés MAX Moteur le quand ieux Dépannage DE GuidePuissance de Entreposage Reglages ET Revision MoteurSionmistrans Avant Roue LA DE PINCEMENT/CARROSSAGE 34 .Fig33 .Fig Fig La Voir Tondeuse DE Lame DE Courroie LA Remplacer Pour Fig LA Voir D’ENTRAÎNEMENT Courroie LA Remplacer PourFreins LES Vérifier Pour 32 .Fig30 .Fig Tondeuse LA Niveau LE Ajuster Pour29 .Fig 28 .Fig25 .Fig 26 .Fig23 .Fig 22 .FigTondeuse LA Enlever Pour Fig Voir21 .Fig GagedEntretien Ligne EN Installe Dessence FiltreFig La Voir Coupe DE Plateau DU Lavage DE Raccord Fig la VoirVentilation DE Système ’ALLUMAGE Bougie’AIR Tamis LE Nettoyer Moteur DE L’HUILE Changer PourLames DES Entretien Fig la Voir Lame LA EnleverPneus Frein DU FonctionnementCe de Réglages et Etretien section la dans réglages les Tous Utilisation Chaque AvantUtilisation Avant ET Réinstallation LA Après Purgée ÊtreTransmission LA Purger 13 .Fig’ESSENCE Réservoir LE Remplir Moteur LE Démarrer PourMoteur DU D’HUILE Niveau LE Vérifier QuetiTondeuse DE Lames LES Arrêter Pour Accessoires Autres ET Charrettes DES Remorquer PourTracteur LE Transporter Pour Pentes LES Dans Utiliser PourFig la Fig la Voir J- Vitess DE Régulateur LE Utiliser CommentTondeuse LA Utiliser Pour Jauge DE Roues LES Régler PourFig la Voir D GAZ DES Commande LA Utiliser PourFig la Voir Mentnetionsta DE Frein LE Engager Pour Tondeuse DE LamesUtilisation Frein DE Pédale Montage Desmancom des fonction la etTionsec la Voir Rouler Faisant LE EN TE Fig la Voir Siège LE Ajustez Assemblé PAS PiècesFig la Voir Batterie LA Vérifier Clés pente-GuideSommaire U1R DimensionCCA .MIN AMP/HR SL-SG-APIEnfants Sécurité DE RèglesTracteurs des sécurité toute en l’utilisation pour Conseils EntretienGénéral Fonctionnement Pentes LES Dans Fonctionnement’éboule bord le si précipiter de ou bord Veuillezlire,comprendreetsuivrelesinstructionsquevoustrouAvertissement REV

96042010800, 430092 specifications

The Poulan 430092, also known by its part number 96042010800, is a high-performance chainsaw that caters to both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Known for its durability, versatility, and user-friendly design, it stands out as a go-to choice in the realm of outdoor equipment.

One of the most notable features of the Poulan 430092 is its powerful engine. Equipped with a robust 40cc two-stroke engine, this chainsaw delivers ample power for cutting through tough wood and handling larger tasks with ease. The engine’s design promotes efficient fuel consumption, allowing for longer use between refueling sessions. This is particularly beneficial for users who need to complete extensive projects without frequent interruptions.

Another characteristic that sets the Poulan 430092 apart is its lightweight design. Weighing under 12 pounds, the chainsaw is easy to maneuver, making it ideal for both aerial pruning and ground-level cutting. Its ergonomic handle provides comfort during extended use, helping to reduce fatigue. Additionally, the chainsaw features an anti-vibration system that absorbs shock, further enhancing user comfort.

The chainsaw is equipped with a 16-inch guide bar and chain, allowing for a greater cutting capacity and making it well-suited for tackling medium to large-sized trees and logs. Its low kickback chain enhances safety, providing peace of mind when operating the saw.

The Poulan 430092 also incorporates advanced technologies such as an automatic oiling system, which ensures that the chain remains well-lubricated during operation. This system prevents excessive wear and tear and prolongs the life of the chainsaw. The easy-access air filter is another innovative feature, allowing users to quickly clean or replace the filter, which helps to maintain optimal engine performance.

In terms of safety, the chainsaw comes with a safety switch that prevents accidental starting, and the chain brake offers additional protection by stopping the chain in case of kickback. These features make the Poulan 430092 not only efficient but also safe for users of all experience levels.

Overall, the Poulan 430092,96042010800 is a reliable and powerful chainsaw that provides excellent performance, user-friendly features, and advanced technologies, making it an excellent investment for anyone needing a dependable cutting tool. Its combination of power, safety, and efficiency continues to earn it a solid reputation in the market for outdoor power equipment.
Top Page Image Contents