Poulan 96042010800 To Level Mower, Turn nut right Turn nut left To raise mower To lower mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 27)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

Fig. 27

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 28)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 28

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 29 & 30) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 29

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (tighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 30

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PB22H46YT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor CJKHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigTo Stop Mower Blades Reverse Operation System ROS See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionMaintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Turn nut right Turn nut left To raise mower To lower mowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigService and Adjustments To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel See FigTransmission Storage OtherFuel System Engine OILTroubleshooting To run when oper Battery will notFires when turn Engine continuesOnly Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeOutdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAGarantie cette de exclus sont normal l’entretien et Dept Service Customer Products Outdoor Canada AuAutorisé Degrés MAX Dépannage DE Guide Moteur le quand ieuxPuissance de Entreposage Sionmistrans Reglages ET RevisionMoteur 33 .Fig Avant Roue LA DE PINCEMENT/CARROSSAGE34 .Fig Fig LA Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour Fig La Voir Tondeuse DE Lame DE Courroie LA Remplacer PourFreins LES Vérifier Pour 32 .FigTondeuse LA Niveau LE Ajuster Pour 30 .Fig29 .Fig 28 .Fig26 .Fig 25 .Fig23 .Fig 22 .FigFig Voir Tondeuse LA Enlever Pour21 .Fig GagedLigne EN Installe Dessence Filtre EntretienFig La Voir Coupe DE Plateau DU Lavage DE Raccord Fig la Voir’ALLUMAGE Bougie Ventilation DE Système’AIR Tamis LE Nettoyer Moteur DE L’HUILE Changer PourFig la Voir Lame LA Enlever Lames DES EntretienPneus Frein DU FonctionnementUtilisation Chaque Avant Ce de Réglages et Etretien section la dans réglages les TousAvant ET Réinstallation LA Après Purgée Être UtilisationTransmission LA Purger 13 .FigMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirMoteur DU D’HUILE Niveau LE Vérifier QuetiAccessoires Autres ET Charrettes DES Remorquer Pour Tondeuse DE Lames LES Arrêter PourTracteur LE Transporter Pour Pentes LES Dans Utiliser PourFig la Voir J- Vitess DE Régulateur LE Utiliser Comment Fig laTondeuse LA Utiliser Pour Jauge DE Roues LES Régler PourGAZ DES Commande LA Utiliser Pour Fig la Voir DFig la Voir Mentnetionsta DE Frein LE Engager Pour Tondeuse DE LamesUtilisation Frein DE Pédale Tionsec la Voir Rouler Faisant LE EN TE MontageDesmancom des fonction la et Assemblé PAS Pièces Fig la Voir Siège LE AjustezFig la Voir Batterie LA Vérifier Clés pente-GuideU1R Dimension SommaireCCA .MIN AMP/HR SL-SG-APISécurité DE Règles EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils EntretienPentes LES Dans Fonctionnement Général Fonctionnement’éboule bord le si précipiter de ou bord Veuillezlire,comprendreetsuivrelesinstructionsquevoustrouREV Avertissement

96042010800, 430092 specifications

The Poulan 430092, also known by its part number 96042010800, is a high-performance chainsaw that caters to both professional landscapers and homeowners who require a reliable tool for various cutting tasks. Known for its durability, versatility, and user-friendly design, it stands out as a go-to choice in the realm of outdoor equipment.

One of the most notable features of the Poulan 430092 is its powerful engine. Equipped with a robust 40cc two-stroke engine, this chainsaw delivers ample power for cutting through tough wood and handling larger tasks with ease. The engine’s design promotes efficient fuel consumption, allowing for longer use between refueling sessions. This is particularly beneficial for users who need to complete extensive projects without frequent interruptions.

Another characteristic that sets the Poulan 430092 apart is its lightweight design. Weighing under 12 pounds, the chainsaw is easy to maneuver, making it ideal for both aerial pruning and ground-level cutting. Its ergonomic handle provides comfort during extended use, helping to reduce fatigue. Additionally, the chainsaw features an anti-vibration system that absorbs shock, further enhancing user comfort.

The chainsaw is equipped with a 16-inch guide bar and chain, allowing for a greater cutting capacity and making it well-suited for tackling medium to large-sized trees and logs. Its low kickback chain enhances safety, providing peace of mind when operating the saw.

The Poulan 430092 also incorporates advanced technologies such as an automatic oiling system, which ensures that the chain remains well-lubricated during operation. This system prevents excessive wear and tear and prolongs the life of the chainsaw. The easy-access air filter is another innovative feature, allowing users to quickly clean or replace the filter, which helps to maintain optimal engine performance.

In terms of safety, the chainsaw comes with a safety switch that prevents accidental starting, and the chain brake offers additional protection by stopping the chain in case of kickback. These features make the Poulan 430092 not only efficient but also safe for users of all experience levels.

Overall, the Poulan 430092,96042010800 is a reliable and powerful chainsaw that provides excellent performance, user-friendly features, and advanced technologies, making it an excellent investment for anyone needing a dependable cutting tool. Its combination of power, safety, and efficiency continues to earn it a solid reputation in the market for outdoor power equipment.
Top Page Image Contents