Poulan 96042007200, 419756 manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•Theattachmentscanalsobeusedduringtheenginewarm- up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage the freewheelleverwhiletheengineisrunning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

1.Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

3.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

4. Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

14

5.Move motion control lever to neutral position. Shut- off engine and set parking brake.

6.Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

7.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

8.Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the motion control lever to the neutral position. Repeat this proce- dure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 15).

Fig. 15

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents XT195H42LT ModelII. Slope Operation Safe Operation Practices for Ride-On MowersGeneral Operation IV. Towing ServiceIII. Children Table of Contents Unassembled Parts Steering WheelBefore Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsPurge Transmission Schedule MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig BatteryTractor Cleaning EngineTo Install Mower See Figs To Remove Mower See FigInstall belt on engine pulley M Mower Tighten Loosen Adjust NUT To Raise To LowerTo Level Mower Loosen JAM NUT a FirstTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products OutdoorCanada Au Garantie cette de exclus sont normal l’entretien etDegrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Défectueux estRalenti Entreposage Réglages ET Révision Rossage Fig la Voir TionsraparéLES Pour Roues LES Enlever Pour AVANT/CAR Roues DES Convergence’EN Courroie LA Remplacer Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourTondeuse DE Lame DE Mentnetraî Freins LES Vérifier Pour29 .Fig Tondeuse LA Niveau LE Ajuster Pour30 .Fig 28 .Fig24 .Fig 26 .Fig25 .Fig 23 .FigFig Voir Cour LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Roie Tondeuse LA Enlever PourEntretien MoteurLames DES Entretien Transmission LA DE RefroidissementFig la Voir Lame LA Enlever PneusUtilisation Chaque Avant O I T a D N a M M O C E RLubrification DE Tableau Tonte DE Conseils UtilisationTransmission LA Purger 15 .Fig’ESSENCE Réservoir LE Remplir Accessoires Autres ET Charrettes DES Remorquer PourMoteur LE Démarrer Pour Tracteur LE Transporter PourJauge DE Roues LES Régler Pour Fig la Voir ROS Arrière CHEMAR EN Fonctionnement DE Système Tondeuse LA Utiliser PourReculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Fig la Voir Arrêter Pour 6 .Fig’OPÉRA DE Présence DE Système DU Commutateur Propriété la de lendommagement Toutes SI Vérifier Toutes SI Vérifier MontageCorrectement Sont Courroies LES PA LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier DU Tracteur LE Sortir PourLE Pour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas SiègeGarantie U1R DimensionSommaire CCA .MIN AMP/HR’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Avertissement

419756, 96042007200 specifications

The Poulan 96042007200,419756 is a versatile and powerful chainsaw designed for both professionals and homeowners. This robust tool is ideal for a variety of tasks including tree trimming, cutting firewood, and general landscaping. Its performance, combined with user-centric features, makes it a popular choice among outdoor enthusiasts.

One of the standout characteristics of the Poulan 96042007200 is its powerful engine. Equipped with a 42cc, 2-cycle engine, this chainsaw delivers impressive cutting power while maintaining a lightweight design, making it easy to maneuver. The engine's efficient design helps it to handle tough jobs without bogging down, ensuring that users can accomplish their tasks with ease.

In terms of technology, the chainsaw features an automatic oiler system. This innovation provides a steady supply of oil to the chain and bar, ensuring optimal lubrication during operation. This feature not only enhances cutting efficiency but also prolongs the life of the chainsaw by reducing wear and tear on the components.

Another important aspect of the Poulan 96042007200,419756 is its ergonomics. The chainsaw is designed with a comfortable grip and an adjustable handle, which allows users to maintain control even during prolonged use. This attention to user comfort translates to less fatigue and more productive working sessions.

Safety is also a key consideration in the design of this chainsaw. The Poulan 96042007200 incorporates a chain brake that helps to prevent accidents by stopping the chain immediately in the event of kickback. Furthermore, the chainsaw is equipped with protective covers to shield the user from debris and other hazards typically associated with cutting tasks.

The chainsaw features a 16-inch bar, which strikes a perfect balance between cutting capacity and maneuverability. This size is suitable for a wide range of cutting jobs, making it adaptable to various user needs. Coupled with a low-profile chain, it delivers smoother cuts and improved control during operation.

Overall, the Poulan 96042007200,419756 is a reliable chainsaw that combines power, technology, and user-friendly features. It is an excellent choice for anyone in need of a dependable cutting tool that can handle a multitude of outdoor tasks efficiently and safely.
Top Page Image Contents