Poulan 419756 manual To Replace Mower Blade Drive Belt See Fig, To Check Brake, Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

MANDRELIDLER

PULLEYPULLEYS

MANDREL

PULLEY

Fig. 31

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT (See Fig. 32)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler (A) and clutching idler (B).

•Remove belt from centerspan idler (C).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

•Remove belt downward from engine pulley (E).

•Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

•Pull belt toward front of tractor and roll belt onto engine pulley (E).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (C).

•Install belt through stationary idler (A) and clutching idler (B).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” section in this manual).

 

E

 

F

A

 

B

G

 

C

 

D

02952

Fig. 32

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model XT195H42LTSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Steering Wheel Unassembled PartsTo Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Unpack CartonInstall Seat See Figs Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigReverse Operation System ROS See Fig To Operate MowerTo Operate on Hills Before Starting the EngineTowing Carts and Other Attachments Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceSchedule Before Each USEBattery TractorBlade Removal See Fig Engine CleaningTo Remove Mower See Fig To Install Mower See FigsInstall belt on engine pulley M To Level Mower Tighten Loosen Adjust NUT To Raise To LowerMower Loosen JAM NUT a FirstTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbFuel System OtherEngine OIL CylindersProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXHOP Outdoor Products Customer Service DeptCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USACanada Au Dept Service Customer Products OutdoorAutorisé Garantie cette de exclus sont normal l’entretien etUNE Pliez EST Ceci Degrés Suivant LESDéfectueux est Dépannage DE GuideRalenti Entreposage Réglages ET Révision LES Pour Roues LES Enlever Pour Fig la Voir TionsraparéRossage AVANT/CAR Roues DES ConvergenceTondeuse DE Lame DE Mentnetraî Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour’EN Courroie LA Remplacer Pour Freins LES Vérifier Pour30 .Fig Tondeuse LA Niveau LE Ajuster Pour29 .Fig 28 .Fig25 .Fig 26 .Fig24 .Fig 23 .FigFigs Voir D’ENTRAÎNEMENT Roie Cour LA ET Tondeuse LA InstallerFig Voir Tondeuse LA Enlever PourMoteur EntretienFig la Voir Lame LA Enlever Transmission LA DE RefroidissementLames DES Entretien PneusO I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Transmission LA Purger UtilisationTonte DE Conseils 15 .FigMoteur LE Démarrer Pour Accessoires Autres ET Charrettes DES Remorquer Pour’ESSENCE Réservoir LE Remplir Tracteur LE Transporter PourMAR EN Fonctionnement DE Système Fig la Voir ROS Arrière CHEJauge DE Roues LES Régler Pour Tondeuse LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourReculer Pour ET Avancer Pour Fig la Voir Arrêter Pour 6 .Fig’OPÉRA DE Présence DE Système DU Commutateur Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier PA LA DE Tracteur LE Retirer Pour LE Pour Exigés Outils LES DU Tracteur LE Sortir PourFig la Voir Batterie LA Vérifier Tionrecdi DE Volant LE FixerSiège Montar SIN PiezasSommaire U1R DimensionGarantie CCA .MIN AMP/HRTracteurs des sécurité toute Général Entretien’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

419756, 96042007200 specifications

The Poulan 96042007200,419756 is a versatile and powerful chainsaw designed for both professionals and homeowners. This robust tool is ideal for a variety of tasks including tree trimming, cutting firewood, and general landscaping. Its performance, combined with user-centric features, makes it a popular choice among outdoor enthusiasts.

One of the standout characteristics of the Poulan 96042007200 is its powerful engine. Equipped with a 42cc, 2-cycle engine, this chainsaw delivers impressive cutting power while maintaining a lightweight design, making it easy to maneuver. The engine's efficient design helps it to handle tough jobs without bogging down, ensuring that users can accomplish their tasks with ease.

In terms of technology, the chainsaw features an automatic oiler system. This innovation provides a steady supply of oil to the chain and bar, ensuring optimal lubrication during operation. This feature not only enhances cutting efficiency but also prolongs the life of the chainsaw by reducing wear and tear on the components.

Another important aspect of the Poulan 96042007200,419756 is its ergonomics. The chainsaw is designed with a comfortable grip and an adjustable handle, which allows users to maintain control even during prolonged use. This attention to user comfort translates to less fatigue and more productive working sessions.

Safety is also a key consideration in the design of this chainsaw. The Poulan 96042007200 incorporates a chain brake that helps to prevent accidents by stopping the chain immediately in the event of kickback. Furthermore, the chainsaw is equipped with protective covers to shield the user from debris and other hazards typically associated with cutting tasks.

The chainsaw features a 16-inch bar, which strikes a perfect balance between cutting capacity and maneuverability. This size is suitable for a wide range of cutting jobs, making it adaptable to various user needs. Coupled with a low-profile chain, it delivers smoother cuts and improved control during operation.

Overall, the Poulan 96042007200,419756 is a reliable chainsaw that combines power, technology, and user-friendly features. It is an excellent choice for anyone in need of a dependable cutting tool that can handle a multitude of outdoor tasks efficiently and safely.
Top Page Image Contents