Poulan 419756, 96042007200 manual Install Seat See Figs

Page 7

ASSEMBLY

INSTALL SEAT (See Figs. 3 and 4)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

Fig. 3

•Push down on seat to engage pads in slots and pull seat towards rear of tractor.

•Raise seat and tighten bolt securely.

•Remove tape and discard.

•Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT

 

TAPE

PAD

 

 

FLAT

 

 

WASHER

 

 

SEAT PAN

 

BOLT

TAB

ADJUSTMENT

HANDLE

 

 

Fig. 4

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

•Raise attachment lift lever to its highest position.

•Releaseparkingbrakebydepressingclutch/brakepedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral position.

•Raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model XT195H42LTGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceIV. Towing Table of Contents Steering Wheel Unassembled PartsUnpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Reverse Operation System ROS See FigCheck Engine OIL Level Before Starting the EngineTo Operate on Hills Towing Carts and Other AttachmentsPurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Removal See Fig Engine CleaningTo Remove Mower See Fig To Install Mower See FigsInstall belt on engine pulley M Loosen JAM NUT a First Tighten Loosen Adjust NUT To Raise To LowerTo Level Mower MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXStevens Creek Road Terry Fox Way Augusta, GA 30907 USA Outdoor Products Customer Service DeptHOP Canada contactGarantie cette de exclus sont normal l’entretien et Dept Service Customer Products OutdoorCanada Au AutoriséUNE Pliez EST Ceci Degrés Suivant LESDéfectueux est Dépannage DE GuideRalenti Entreposage Réglages ET Révision AVANT/CAR Roues DES Convergence Fig la Voir TionsraparéLES Pour Roues LES Enlever Pour RossageFreins LES Vérifier Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourTondeuse DE Lame DE Mentnetraî ’EN Courroie LA Remplacer Pour28 .Fig Tondeuse LA Niveau LE Ajuster Pour30 .Fig 29 .Fig23 .Fig 26 .Fig25 .Fig 24 .FigTondeuse LA Enlever Pour Cour LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Roie Fig VoirMoteur EntretienPneus Transmission LA DE RefroidissementFig la Voir Lame LA Enlever Lames DES EntretienLubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant 15 .Fig UtilisationTransmission LA Purger Tonte DE ConseilsTracteur LE Transporter Pour Accessoires Autres ET Charrettes DES Remorquer PourMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirTondeuse LA Utiliser Pour Fig la Voir ROS Arrière CHEMAR EN Fonctionnement DE Système Jauge DE Roues LES Régler PourFig la Voir Arrêter Pour 6 .Fig GAZ DES Commande LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Reculer Pour ET Avancer Pour’OPÉRA DE Présence DE Système DU Commutateur Propriété la de lendommagement Correctement Sont Courroies LES MontageToutes SI Vérifier Toutes SI Vérifier PA LA DE Tracteur LE Retirer Pour Tionrecdi DE Volant LE Fixer DU Tracteur LE Sortir PourLE Pour Exigés Outils LES Fig la Voir Batterie LA VérifierSiège Montar SIN PiezasCCA .MIN AMP/HR U1R DimensionSommaire Garantie’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute ’utilisation pour ConseilsLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

419756, 96042007200 specifications

The Poulan 96042007200,419756 is a versatile and powerful chainsaw designed for both professionals and homeowners. This robust tool is ideal for a variety of tasks including tree trimming, cutting firewood, and general landscaping. Its performance, combined with user-centric features, makes it a popular choice among outdoor enthusiasts.

One of the standout characteristics of the Poulan 96042007200 is its powerful engine. Equipped with a 42cc, 2-cycle engine, this chainsaw delivers impressive cutting power while maintaining a lightweight design, making it easy to maneuver. The engine's efficient design helps it to handle tough jobs without bogging down, ensuring that users can accomplish their tasks with ease.

In terms of technology, the chainsaw features an automatic oiler system. This innovation provides a steady supply of oil to the chain and bar, ensuring optimal lubrication during operation. This feature not only enhances cutting efficiency but also prolongs the life of the chainsaw by reducing wear and tear on the components.

Another important aspect of the Poulan 96042007200,419756 is its ergonomics. The chainsaw is designed with a comfortable grip and an adjustable handle, which allows users to maintain control even during prolonged use. This attention to user comfort translates to less fatigue and more productive working sessions.

Safety is also a key consideration in the design of this chainsaw. The Poulan 96042007200 incorporates a chain brake that helps to prevent accidents by stopping the chain immediately in the event of kickback. Furthermore, the chainsaw is equipped with protective covers to shield the user from debris and other hazards typically associated with cutting tasks.

The chainsaw features a 16-inch bar, which strikes a perfect balance between cutting capacity and maneuverability. This size is suitable for a wide range of cutting jobs, making it adaptable to various user needs. Coupled with a low-profile chain, it delivers smoother cuts and improved control during operation.

Overall, the Poulan 96042007200,419756 is a reliable chainsaw that combines power, technology, and user-friendly features. It is an excellent choice for anyone in need of a dependable cutting tool that can handle a multitude of outdoor tasks efficiently and safely.
Top Page Image Contents