Poulan 96042007200 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

1/2" wrench

Utility knife

(2)

3/4" wrench

Tire pressure gauge

 

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

BOLT

LOCK

WASHER

LARGE

FLAT WASHER

STEERING

WHEEL

STEERING

BOOT

ADAPTER

TABS

EXTENSION SHAFT

TAB SLOTS

LOWER STEERING SHAFT

03132

Fig. 1

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

BATTERY BOX

DOOR

TERMINAL

TERMINAL

02021

Fig. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents XT195H42LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Unassembled Parts Steering WheelBefore Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Schedule MaintenanceGeneral Recommendations Before Each USEBattery TractorBlade Removal See Fig Cleaning EngineTo Install Mower See Figs To Remove Mower See FigInstall belt on engine pulley M Mower Tighten Loosen Adjust NUT To Raise To LowerTo Level Mower Loosen JAM NUT a FirstTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeCanada contact Outdoor Products Customer Service DeptHOP Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAAutorisé Dept Service Customer Products OutdoorCanada Au Garantie cette de exclus sont normal l’entretien etDegrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Défectueux estRalenti Entreposage Réglages ET Révision Rossage Fig la Voir TionsraparéLES Pour Roues LES Enlever Pour AVANT/CAR Roues DES Convergence’EN Courroie LA Remplacer Pour Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl PourTondeuse DE Lame DE Mentnetraî Freins LES Vérifier Pour29 .Fig Tondeuse LA Niveau LE Ajuster Pour30 .Fig 28 .Fig24 .Fig 26 .Fig25 .Fig 23 .FigFig Voir Cour LA ET Tondeuse LA InstallerFigs Voir D’ENTRAÎNEMENT Roie Tondeuse LA Enlever PourEntretien MoteurLames DES Entretien Transmission LA DE RefroidissementFig la Voir Lame LA Enlever PneusO I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Tonte DE Conseils UtilisationTransmission LA Purger 15 .Fig’ESSENCE Réservoir LE Remplir Accessoires Autres ET Charrettes DES Remorquer PourMoteur LE Démarrer Pour Tracteur LE Transporter PourJauge DE Roues LES Régler Pour Fig la Voir ROS Arrière CHEMAR EN Fonctionnement DE Système Tondeuse LA Utiliser PourReculer Pour ET Avancer Pour GAZ DES Commande LA Utiliser PourFig la Voir Mentne -TIONSTA DE Frein LE Engager Pour Fig la Voir Arrêter Pour 6 .Fig’OPÉRA DE Présence DE Système DU Commutateur Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier PA LA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier DU Tracteur LE Sortir PourLE Pour Exigés Outils LES Tionrecdi DE Volant LE FixerMontar SIN Piezas SiègeGarantie U1R DimensionSommaire CCA .MIN AMP/HR’utilisation pour Conseils Général EntretienTracteurs des sécurité toute ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils Avertissement

419756, 96042007200 specifications

The Poulan 96042007200,419756 is a versatile and powerful chainsaw designed for both professionals and homeowners. This robust tool is ideal for a variety of tasks including tree trimming, cutting firewood, and general landscaping. Its performance, combined with user-centric features, makes it a popular choice among outdoor enthusiasts.

One of the standout characteristics of the Poulan 96042007200 is its powerful engine. Equipped with a 42cc, 2-cycle engine, this chainsaw delivers impressive cutting power while maintaining a lightweight design, making it easy to maneuver. The engine's efficient design helps it to handle tough jobs without bogging down, ensuring that users can accomplish their tasks with ease.

In terms of technology, the chainsaw features an automatic oiler system. This innovation provides a steady supply of oil to the chain and bar, ensuring optimal lubrication during operation. This feature not only enhances cutting efficiency but also prolongs the life of the chainsaw by reducing wear and tear on the components.

Another important aspect of the Poulan 96042007200,419756 is its ergonomics. The chainsaw is designed with a comfortable grip and an adjustable handle, which allows users to maintain control even during prolonged use. This attention to user comfort translates to less fatigue and more productive working sessions.

Safety is also a key consideration in the design of this chainsaw. The Poulan 96042007200 incorporates a chain brake that helps to prevent accidents by stopping the chain immediately in the event of kickback. Furthermore, the chainsaw is equipped with protective covers to shield the user from debris and other hazards typically associated with cutting tasks.

The chainsaw features a 16-inch bar, which strikes a perfect balance between cutting capacity and maneuverability. This size is suitable for a wide range of cutting jobs, making it adaptable to various user needs. Coupled with a low-profile chain, it delivers smoother cuts and improved control during operation.

Overall, the Poulan 96042007200,419756 is a reliable chainsaw that combines power, technology, and user-friendly features. It is an excellent choice for anyone in need of a dependable cutting tool that can handle a multitude of outdoor tasks efficiently and safely.
Top Page Image Contents