Poulan PO16542B manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 9)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

 

CENTER

 

HOLE

LOCK WASHER

STAR

BLADE

FLAT WASHER

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 9

TO SHARPEN BLADE (See Fig. 10)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 10

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PO16542B II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeysTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportMowing Tips ADD GasolineTo Start Engine See Fig General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Attach Jumper Cables To Adjust Steering Wheel AlignmentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWhen operator leaves Tractor - Model Number PO16542B, Product no 56 SchematicElectrical KEY Part Description Chassis and Enclosures Saddle Slkscr Flat Lt 6 Sp Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine 148315 Seat Assembly Wheels & Tires DecalsMower Lift 159460 Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

PO16542B specifications

The Poulan PO16542B is a robust and versatile lawn mower designed for homeowners and landscapers seeking reliability and ease of use. This model stands out in the crowded market of outdoor power equipment due to its thoughtful engineering and practical features.

Equipped with a 42-inch cutting deck, the PO16542B ensures that users can cover large areas effectively, reducing the need for multiple passes. This size strikes a balance between maneuverability and efficiency, making it ideal for medium-sized yards. The cutting deck is adjustable, allowing users to select from various cutting heights, which enables them to achieve the desired finish for their lawn.

One of the key technologies incorporated into the PO16542B is its powerful 16.5 HP Briggs & Stratton engine. Known for its reliability, this engine provides ample power to tackle tough grass and uneven terrain. The engine's design allows for easy starting, which is a significant convenience for users eager to get their mowing tasks done quickly.

Another notable feature of the Poulan PO16542B is its easy-to-use transmission system. The lawn mower includes a hydrostatic transmission that provides smooth and effortless speed adjustments. This ensures that users can control their mowing speed precisely, making for a more tailored mowing experience. Whether navigating around flower beds or cutting in straight lines across open lawns, this feature enhances maneuverability.

Comfort is also prioritised in the design of the PO16542B. The mower features an ergonomically designed seat that provides adequate support during long mowing sessions. Coupled with easy-access controls positioned conveniently at hand, it promotes user-friendly operation, reducing fatigue over extended periods.

Additionally, the Poulan PO16542B is built with durability in mind. Its sturdy construction and high-quality materials ensure that the mower can withstand the rigors of regular use. This longevity is complemented by the ease of maintenance, with features such as easy-access oil and filter changes.

Overall, the Poulan PO16542B presents a compelling package for those looking for a reliable, efficient, and comfortable mower. With its combination of power, adaptability, and user-centric design, it stands out as a formidable choice for lawn care, making the chore of mowing not just manageable, but enjoyable.
Top Page Image Contents