Poulan PO16542B manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

 

OF MOWER TO

OF MOWER TO

 

 

GROUND

GROUND

 

 

 

A

GROUND LINE

A

FIG. 17

SUSPENSION

ARM

LIFT LINK ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”“D”

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “E”

NUT “F”

FRONT

LINKSTRUNNION

FIG. 20

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. PO16542B Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatKeys Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig Lower seat into operating position and sit on seatCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsADD Gasoline Lubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Replacing Battery See FigsFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PO16542B, Product no 56Electrical KEY Part Description Chassis and Enclosures Saddle Slkscr Flat Lt 6 Sp Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine 148315 Seat Assembly Decals Wheels & TiresMower Lift 159460 Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

PO16542B specifications

The Poulan PO16542B is a robust and versatile lawn mower designed for homeowners and landscapers seeking reliability and ease of use. This model stands out in the crowded market of outdoor power equipment due to its thoughtful engineering and practical features.

Equipped with a 42-inch cutting deck, the PO16542B ensures that users can cover large areas effectively, reducing the need for multiple passes. This size strikes a balance between maneuverability and efficiency, making it ideal for medium-sized yards. The cutting deck is adjustable, allowing users to select from various cutting heights, which enables them to achieve the desired finish for their lawn.

One of the key technologies incorporated into the PO16542B is its powerful 16.5 HP Briggs & Stratton engine. Known for its reliability, this engine provides ample power to tackle tough grass and uneven terrain. The engine's design allows for easy starting, which is a significant convenience for users eager to get their mowing tasks done quickly.

Another notable feature of the Poulan PO16542B is its easy-to-use transmission system. The lawn mower includes a hydrostatic transmission that provides smooth and effortless speed adjustments. This ensures that users can control their mowing speed precisely, making for a more tailored mowing experience. Whether navigating around flower beds or cutting in straight lines across open lawns, this feature enhances maneuverability.

Comfort is also prioritised in the design of the PO16542B. The mower features an ergonomically designed seat that provides adequate support during long mowing sessions. Coupled with easy-access controls positioned conveniently at hand, it promotes user-friendly operation, reducing fatigue over extended periods.

Additionally, the Poulan PO16542B is built with durability in mind. Its sturdy construction and high-quality materials ensure that the mower can withstand the rigors of regular use. This longevity is complemented by the ease of maintenance, with features such as easy-access oil and filter changes.

Overall, the Poulan PO16542B presents a compelling package for those looking for a reliable, efficient, and comfortable mower. With its combination of power, adaptability, and user-centric design, it stands out as a formidable choice for lawn care, making the chore of mowing not just manageable, but enjoyable.
Top Page Image Contents