Poulan PO16542B manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 1/2 hex nut and tighten se- curely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

STEERING

 

WHEEL INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

 

STEERING

 

WHEEL

STEERING

 

BOOT

 

 

TABS

ADAPTER

EXTENSION

 

 

SHAFT

1/4 LOCKNUT

 

 

1/4 HEX BOLT

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

Lift seat pan to raised position.

If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in CUSTOMER RESPONSIBILITIES section of this manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

FIG. 2

6

Image 6
Contents Model NO. PO16542B General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Keys Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWhen operator leaves Schematic Tractor - Model Number PO16542B, Product no 56Electrical KEY Part Description Chassis and Enclosures Saddle Slkscr Flat Lt 6 Sp Drive Transaxle Peerless Model 206-545C Steering Assembly KEY Part NO. NO. Description Engine 148315 Seat Assembly Decals Wheels & TiresMower Lift 159460 Mower Deck Repair Parts Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

PO16542B specifications

The Poulan PO16542B is a robust and versatile lawn mower designed for homeowners and landscapers seeking reliability and ease of use. This model stands out in the crowded market of outdoor power equipment due to its thoughtful engineering and practical features.

Equipped with a 42-inch cutting deck, the PO16542B ensures that users can cover large areas effectively, reducing the need for multiple passes. This size strikes a balance between maneuverability and efficiency, making it ideal for medium-sized yards. The cutting deck is adjustable, allowing users to select from various cutting heights, which enables them to achieve the desired finish for their lawn.

One of the key technologies incorporated into the PO16542B is its powerful 16.5 HP Briggs & Stratton engine. Known for its reliability, this engine provides ample power to tackle tough grass and uneven terrain. The engine's design allows for easy starting, which is a significant convenience for users eager to get their mowing tasks done quickly.

Another notable feature of the Poulan PO16542B is its easy-to-use transmission system. The lawn mower includes a hydrostatic transmission that provides smooth and effortless speed adjustments. This ensures that users can control their mowing speed precisely, making for a more tailored mowing experience. Whether navigating around flower beds or cutting in straight lines across open lawns, this feature enhances maneuverability.

Comfort is also prioritised in the design of the PO16542B. The mower features an ergonomically designed seat that provides adequate support during long mowing sessions. Coupled with easy-access controls positioned conveniently at hand, it promotes user-friendly operation, reducing fatigue over extended periods.

Additionally, the Poulan PO16542B is built with durability in mind. Its sturdy construction and high-quality materials ensure that the mower can withstand the rigors of regular use. This longevity is complemented by the ease of maintenance, with features such as easy-access oil and filter changes.

Overall, the Poulan PO16542B presents a compelling package for those looking for a reliable, efficient, and comfortable mower. With its combination of power, adaptability, and user-centric design, it stands out as a formidable choice for lawn care, making the chore of mowing not just manageable, but enjoyable.